Magnavox 60p8241 manual More PIP Connections

Page 50

Picture-in-Picture (PIP) • More Connections

MORE PIP CONNECTIONS

This page shows how to hook PIP up with a cable box and a VCR.

BEGIN

First, use an optional signal splitter and connect the original cable TV signal to both the CABLE IN on the cable converter and the ANTEN-

3

Back of TV

NA plug on the rear of the television.

Connect the CABLE OUT on the Converter to the ANTENNA IN on the VCR.

Connect the VIDEO OUT jack on the VCR to the VIDEO IN jack on the TV.

Also connect the AUDIO OUT (right and left) jacks from the VCR to the AUDIO IN jacks on the television.

ANTENNA IN 75Ω

MONITOR OUT

VIDEO

MONO/L

AUDIO

R

AV1 IN

Y

Pb

Pr

AV2 IN

S-VIDEO

1

Signal

Splitter

Contact the Parts Information Center at 1-800-851-8885 to order any optional accessories.

SMART HELP

Remember, to use the cable TV converter box to

select channels for PIP, the VCR must be set to the same channel as the channel selection switch on the back of the cable converter (either channel 3 or 4).

Video Cables	Audio Cables
(Yellow)	(Red and White)

OUT	OUT
ANTENNA
OUT
VIDEO	R AUDIO L
ANTENNA
IN
IN	IN

VCR

2

CABLE OUT

CABLE IN

Cable TV Converter

50

Image 50

Contents Projection Television Warranty OwnerModel Verification Confirmation Registration Important Safety Instructions Table of Contents Features Digital-Ready Projection TVAdjusting the Picture Press the Cursor Right buttonTurning on the Dynamic Noise Reduction DNR Control Press the i+ button to removeTurning on the Imagemax Control Converge RED/BLUE Converge Multipoint RED/BLUE Navigate1410 Press the i+ button to enterUndo Multipoint Press the Menu button to showSetting the Clock Press the Cursor Right button to enter the Features menuSetting the Start Time Press the Cursor RightSetting the Stop Time Selecting the Channel Press the Number buttons toSetting the Activate Control Constantly Displaying the Time on Screen Understanding Autolock Movie RatingsEnter a new four-digit code Setting UP the Access CodeThen press the Cursor Down Enter your new four-digit codeMenu. Then press the Cursor Enter your four-digit AccessBlocking Channels Press the Cursor UP orEnter your four-digit Access CODE. Correct will flash very Blocking by Movie RatingPress the Cursor Down Enter your four-digit Access CodeBlocking by TV Rating Press the Cursor UP or Down button to select a ratingTurning the Blocking Control on or OFF Press the i+ button to remove the menuTon again to highlight Access Code Blocking Unrated BroadcastsBlocking Broadcasts That have no Rating Press the Cursor Right or Left button to turn no RatingReviewing Your Settings Block Unrated No RatingClearing ALL Blocked Channels Enter your four-digitPress the Cursor UP or Down button to select a Caption Using the Closed Captioning ControlLighted. Then press the Cursor Adjusting the TREBLE, BASS, and Balance TrebleUsing the AVL Audio Volume Leveler Control Using Incredible Surround Cursor Right or Left butSetting the TV for Stereo and SAP Setting the Audio OUT Control Using the TV Speaker Control and Audio Outputs Using the Bass Boost Control Press the Smartpicture button repeatedly to select either Using SmartpicturePress the Smartpicture Using Smartsound SmartSound ChoicesUsing Surf and Alternate Channel SurfUsing the Sleep Timer Control Using the Volume and AV Buttons Press the Volume +,- butSetting the TV Remote to Work Accessory Devices VCRMove the slide switch on the side Point the remote at the accessorySearch Method VCR player stops, the correct codeSetting the TV Remote to Work Accessories See the next page for more codesSatellite Receiver Brand Remote Codes Using PIP Basic Connections Using the PIP Remote Control Buttons Press the PIP ON/OFF button toAdjusting the PIP Color and Tint Controls Press the MENU/SELECT butMore PIP Connections Helpful Hints Glossary of Television Terms Index Renewed