Magnavox 60p8241 manual Using PIP Basic Connections

Page 47

Picture-in-Picture (PIP) • Basic Connections

USING PIP (BASIC CONNECTIONS)

Picture-In-Picture (PIP) is the showing of two pictures on the TV

PIP Window

Back of TV

2

screen at the same time—one main screen picture and one small picture, or PIP.

NOTE: The PIP picture must be sup- plied by a VCR (or other accessory device equipped with a VIDEO OUT[PUT] jack). The following con- nection example uses the AV1 IN(puts), but you may use AV2 instead, if you would like.

BEGIN

Connect an antenna or cable TV

signal to the ANTENNA IN(put) on the back of the VCR.

Connect the VIDEO OUT jack

on the VCR to the AV1 IN(put) for VIDEO on the back of the TV.

Main Screen

Outdoor or

Indoor

Antenna

OR

Cable TV Signal

VCR in

3

TV Mode

 

ANTENNA IN 75Ω

MONITOR OUT

AV1 IN

AV2 IN

Y

VIDEO

S-VIDEO

MONO/L

AUDIO

R

Back of VCR

OUT

OUT

ANTENNA

 

OUT

 

VIDEO

L AUDIO R

ANTENNA

 

IN

 

IN

IN

1

Also connect the AUDIO OUT(puts) (R and L) jacks from the VCR to the AV1 IN(puts) (R and L) for AUDIO on the back of the TV.

Turn the VCR and TV on. Place the VCR in TV mode—Use

the VCR/TV button on the VCR.

Press the PIP on/off button on

the TV remote.

The PIP window should show in one of the corners of the TV screen.

Press the PIP SOURCE button

on your TV remote until the input source to which you connected your VCR (in this example, AV 1) appears in the PIP window.

Select the channel on the VCR to view in the PIP window. You can do this with your TV remote (in VCR mode) if you have set it to work with your VCR (see page 42).

Put the TV/VCR/ACC switch on the remote in TV mode and select the channel on the TV to view on the main screen.

 

12:00 VCR

 

 

12:00

06

 

 

 

 

 

06

 

 

6

Channel Selection

 

Through VCR

 

 

12:00

19

5

 

 

 

 

 

SMART HELP

Remember, be sure the TV remote is in the correct mode

when you switch back and forth between the VCR and the TV.

If you see the same picture on the main screen and in the PIP window, you need to be sure you have select- ed the source to which you connected the VCR.

For other possible PIP connections see the “More PIP Connections” section.

If you have a single (monaural) audio output VCR, “Y” connectors are available to complete your connec- tion. Contact your dealer, or our Parts Information Center at

1-800-851-8885 for details.

4

AV

i+

SAP

TV

 

 

VCR

1

2

3

ACC

4

5

6

 

 

7

8

9

 

SMART

 

SMART

0

MENUSURF

CH

INCR. SURR.

PIP

A/CH

 

 

PIP CH

 

UP

DN

NOTE: When selecting channels on the VCR for the PIP window, use the CH(annel) Scan (+, —) buttons rather than the PIP CH(annel) UP/DN buttons.

47

Page 46 Page 48
Image 47
Page 46 Page 48
Contents Projection Television Warranty OwnerModel Verification Confirmation Registration Important Safety Instructions Table of Contents Digital-Ready Projection TV FeaturesPress the Cursor Right button Adjusting the PicturePress the i+ button to remove Turning on the Dynamic Noise Reduction DNR ControlTurning on the Imagemax Control Converge RED/BLUE Navigate Converge Multipoint RED/BLUEPress the i+ button to enter 1410Press the Menu button to show Undo MultipointPress the Cursor Right button to enter the Features menu Setting the ClockPress the Cursor Right Setting the Start TimeSetting the Stop Time Press the Number buttons to Selecting the ChannelSetting the Activate Control Constantly Displaying the Time on Screen Movie Ratings Understanding AutolockEnter your new four-digit code Setting UP the Access CodeThen press the Cursor Down Enter a new four-digit codePress the Cursor UP or Enter your four-digit AccessBlocking Channels Menu. Then press the CursorBlocking by Movie Rating Enter your four-digit Access CODE. Correct will flash veryPress the Cursor UP or Down button to select a rating Enter your four-digit Access CodeBlocking by TV Rating Press the Cursor DownPress the i+ button to remove the menu Turning the Blocking Control on or OFFBlocking Unrated Broadcasts Ton again to highlight Access CodePress the Cursor Right or Left button to turn no Rating Blocking Broadcasts That have no RatingBlock Unrated No Rating Reviewing Your SettingsEnter your four-digit Clearing ALL Blocked ChannelsPress the Cursor UP or Down button to select a Caption Using the Closed Captioning ControlLighted. Then press the Cursor Treble Adjusting the TREBLE, BASS, and BalanceUsing the AVL Audio Volume Leveler Control Cursor Right or Left but Using Incredible SurroundSetting the TV for Stereo and SAP Setting the Audio OUT Control Using the TV Speaker Control and Audio Outputs Using the Bass Boost Control Press the Smartpicture button repeatedly to select either Using SmartpicturePress the Smartpicture SmartSound Choices Using SmartsoundSurf Using Surf and Alternate ChannelUsing the Sleep Timer Control Press the Volume +,- but Using the Volume and AV ButtonsVCR Setting the TV Remote to Work Accessory DevicesPoint the remote at the accessory Move the slide switch on the sideVCR player stops, the correct code Search MethodSee the next page for more codes Setting the TV Remote to Work AccessoriesSatellite Receiver Brand Remote Codes Using PIP Basic Connections Press the PIP ON/OFF button to Using the PIP Remote Control ButtonsPress the MENU/SELECT but Adjusting the PIP Color and Tint ControlsMore PIP Connections Helpful Hints Glossary of Television Terms Index Renewed
Top Page Image Contents