Fostex D2424LV manual Connecting a digital mixer, Digital mixer

Page 14

Model D2424LV Quick Operation Guide

Connecting a digital mixer

When making connections with a digital recording mixer, refer to the connecting example below.

<CAUTION>

•When connecting the recorder to a digital mixing console, make sure that the power of both units are off.

•The [DATA INPUT] and [DATA OUTPUT] connectors do not support adat digital signals of 96-kHz Fs. In other words, the unit cannot receive of feed an adat digital signal of 96-kHz Fs.

Digital mixer

<adat digital signal>

[DATA IN/OUTPUT] 1-8,9-16 and 17-24 can all be used for record/playback of adat digital signals. Signals to [DATA INPUT] 1-8,9-16 and 17-24 will, re- spectively, be assigned to tracks 1-8,9-16 and 17- 24, and recorded.

At playback, the track outputs are respectively assigned from each [DATA OUTPUT] connectors in the same manner.

<Note>: Except for 96-kHz Fs adat digital signals.

<S/P DIF digital signal>

At record/playback of S/P DIF digital signals, in- put connectors [DATA INPUT] 1-8only can be used and the output ports will be [DATA OUTPUT] 1-8, 9- 16 and 17-24.

Signals input to [DATA INPUT] 1-8will be assigned and recorded in tracks 1 and 2.

At playback, signals output from track 1-2, 3-4 and 5-6 will be, respectively, assigned and out- put from [DATA OUTPUT] 1-8, 9-16and 17-24.

DATA IN 17-24

DATA IN 9-16

DATA IN 1-8

TRK 24

TRK 23

TRK 22

TRK 21

TRK 20

TRK 19

TRK 18

TRK 17

TRK 16

TRK 15

TRK 14

TRK 13

TRK 12

TRK 11

TRK 10

TRK 9

TRK 8

TRK 7

TRK 6

TRK 5

TRK 4

TRK 3

TRK 2 TRK 1

DATA OUT 17-24

DATA OUT 9-16

DATA OUT 1-8

DATA IN 1-8

TRK 24

TRK 23

TRK 22

TRK 21

TRK 20

TRK 19

TRK 18

TRK 17

TRK 16

TRK 15

TRK 14

TRK 13

TRK 12

TRK 11

TRK 10

TRK 9

TRK 8

TRK 7

TRK 6

TRK 5

TRK 4

TRK 3

TRK 2 TRK 1

DATA OUT 17-24

DATA OUT 9-16

DATA OUT 1-8

14

Image 14

Contents Quick Operation Guide Model D2424LV Quick Operation Guide Safety Instructions Contents Package contents Recording mediaDisassembling the caddy Installing a hard disk in the caddyPreparation for the current drive Assembling the case Connecting cablesFixing the hard disk to the case Installing the removable case in the recorder Connecting a detachable controllerPress the EXECUTE/YES key Turn the power onSampling frequency Format type Program Time BaseSetup of the Internal Clock Press the Setup key while in the stop modeConnecting a analog mixer Analog mixerConnecting a digital mixer Digital mixerHints Initial settingsAbout Sampling Frequency Basic analog recording Adjusting the recording levelBasic recording Stopping recordingTo cancel the undo operation, press the UNDO/ Redo key again Undo and redo recording single undo/redoSelecting Digital Out Basic digital recordingSelecting Digital About Digital In selectionPress the EXIT/NO key or Stop button to exit the Setup mode Setting the reference clockAbout reference clock setting Press the Record button once Multitrack recording using overdubbingPing-pong recording PlaybackLocating the top of the Program MixdownBasic Locate function Locating the end of the recorded area of the ProgramRecording in a new Program Selecting the desired ProgramCurrent drive formatting by 16bit Changing the program FSCurrent drive formatting by 24bit Set the desired pitch data using the Jog dial Playback using theVari-pitch functionVari-pitch function procedures Press the Recall key, then press the Vari Pitch keyReference manual reference pages Declaration of EC Directive Memo Fostex Corporation