Fostex VR800 owner manual Ejecting a removable disk from the Scsi drive

Page 12

VR800 Quick Operation Guide

DIGITAL

44.1kHz

SETUP

SYNC OUT

CLK

AUTO

DRIVE

SCSI

A.PUNCH

2 Turn the JOG dial to select [Format ?] and press the EXECUTE/YES key.

The VR800 displays the ID number of the connected SCSI drive and flashes [SURE ?].

DIGITAL

44.1kHz

DIGITAL

44.1kHz

 

SETUP

 

SETUP

SYNC OUT

CLK

AUTO

DRIVE

SCSI

A.PUNCH

SURE ?

SYNC OUT

AUTO

DRIVE

SCSI

A.PUNCH

3 Use the JOG dial to select the desired record mode.

Ejecting a removable disk from the SCSI drive

Follow the procedure below to eject a removable disk from the SCSI drive after the VR800 exits the setup mode and disk access has stopped. You cannot eject a removable disk using the eject button on the drive.

1 Press and hold down the SHIFT key and press the EXIT/NO key.

The removable disk will be eject from the current SCSI drive.

Before turning off the power to the VR800

Before turning off the power to the VR800 and the connected SCSI drive, check the following items:

*The SCSI disk is not being accessed. (The ACCESS LED is turned off.)

*The VR800 has exited the setup mode and displays the ABS or BAR/BEAT/CLK time base.

*The output volume of the VR800 all connected audio devices is set to minimum.

Turning on the power again with a removable disk loaded in the SCSI drive

There is no procedure for turning on the power without a removable disk loaded in the SCSI drive but if power is switched off with a disk, and then power needs to be switched on again, follow the procedure below:

1

First, turn on the power to the SCSI drive loaded with the removable disk.

 

 

2

First, make sure that the orange LED on the SCSI drive lights up in green and that the

 

removable disk is not being accessed, and then turn on the power to the VR800.

 

 

12

Image 12
Contents Model Quick Operation GuideSafety Instructions Table of Contents Using an E-IDE hard disk Recording mediaInstalling an E-IDE hard disk in the VR800 Install the included brackets on the hard diskReplacescrews. the bottom panel using the same six Place the VR800 on the flat level surface soUsing a Scsi drive Connecting a Scsi drive to the VR800Scsi ID number setting Turn on the power to the connected Scsi drive and the VR800 Formatting initializing a diskInsert a disk in the Scsi drive When SURE? appears, press the EXECUTE/YES key Use the JOG dial to select the desired record modePress the EXIT/NO key to quit the setup mode IDE will light For details, refer toChecking the record mode of the formatted disk Press the Setup key to change to Setup modeChecking available recording time on a formatted disk Formatting the disk againBefore turning off the power to the VR800 Ejecting a removable disk from the Scsi drivePress and hold down the Shift key and press the EXIT/NO key Scsi drive is the current drive Connecting a mixer Connecting a digital mixer equipped with adat I/OConnecting an analog mixing console About changing the digital-in clock settingInitial settings Basic recordingAbout sampling frequency Basic recording procedure MixerPress the Record button once. The Record button lamp To cancel the undo operation, press the UNDO/REDO key again Undo and redo recordingPress the Stop button to finish recording Press the Play buttonMultitrack recording using overdubbing When you finish overdubbing, stop the VR800, locatePing-pong recording Press the Record button onceMixdown Recording in a new programBasic Locate function Selecting the desired program from multiple programsLocating the top of the program Locating the end of the recorded area of the programPlayback using the Vari-pitch function Procedures vari pitch functionKey To turn off vari pitch mode, press the Vari Pitch keyReference pages Fostex Corporation
Related manuals
Manual 122 pages 2.66 Kb