Vidikron VL-46 manual 100

Page 53

Save Settings: For each input and supported resolution, the DView lets you save image quality settings as presets that you can recall at a later time. You can create up to three presets – designated “Custom,” “ISF Day” and “ISF Night” – per input and resolution.

You should save changes to any of the following settings to a preset; otherwise they will be lost when a new input source or resolution is selected:

Brightness

Contrast

Color saturation

Tint

Sharpness

Gamma

Color temperature and white balance

To save image settings to a preset, select Save Settings from the ISF Calibration menu and select “Custom,“ “ISF Day” or “ISF Night.”

White Balance: To remove any trace of color from the white areas of the projected image, choose White Balance from the Picture Adjust menu and press ENTER.

Gain: Use the Gain controls to correct color imbalances in the bright areas of the image. A good way to do this is to use a test pattern consisting mostly of solid white areas, such as an 80 IRE “window” pattern. If the white areas contain traces of red, green or blue, decrease the Gain for that color.

Offset: Use the Offset controls in the White Balance sub-menu to correct color imbalances in the dark areas of the image. A good way to do this is to use a test pattern consisting mostly of dark gray areas, such as a 30 IRE “window” pattern. If the gray areas contain traces of red, green or blue, decrease the Offset for that color.

Any white balance adjustments you make here are automatically stored

Note

as a “Custom” color temperature.

 

White Balance

R Gain

100

G Gain

100

B Gain

100

R Offset

50

G Offset

50

B Offset

50

 

 

Blue Enable: Blue Enable removes all red and green color information from the image, simulating a blue filter. You can use it instead of a blue filter when performing color and tint adjustments.

Baud Rate: Select Baud Rate from the ISF Calibration menu to set the data transfer rate of the DView’s RS-232 SERVICE port. (This setting must match the data rate of the device connected to the RS-232 input.)

Serial Link: Select Serial Link from the ISF Calibration menu to configure the RS-232 Service port (see Figure 3-11)for normal operation (On) or for software upgrades (Off).

Factory Reset: To reset all DView settings to their factory defaults, select Factory Reset from the ISF Calibration menu and press ENTER. This command is not undoable. Use it with caution!

Vidikron VL-40 and VL-46 Owner’s Operating Manual

43

Image 53
Contents VL-40 and VL-46 Page For LCD Displays ONE Year Limited WarrantyRIGHTS, Limits and Exclusions Vidikron DOC Compliance Notice Safety Precautions1Table of Contents Specifications Maintenance and TroubleshootingOperation Serial Communications1List of Figures List of Figures About This Manual 1IntroductionThey also provide supplemental information Using This ManualPerformance or cause a malfunction If you need Turn toKey Features and Benefits Description, Features and BenefitsOptional Accessories 2Controls and Functions Controls and IndicatorsDView at a Glance SpeakersPower Input 100 to 240 VAC Connect the DView to power here Headphone Jack Main Power SwitchINPUT2 S-Video Input RGBINPUT4 Component Video RCA connectors INPUT3 Component Video RCA connectorsHDMI1/Computer Input Digital HDMI2/Computer Input Digital PC Audio InputDView Remote Control DView Remote ControlOFF / on Memory Preset ButtonsNumeric Buttons Source Selection Buttons4X3 Aspect Ratio Selection Buttons ANALetbox Letterbox Wide IntelliWideSound Control Buttons Timer OFF ButtonSurrnd Surround MTS/SAP Multichannel Television Sound/Second Audio ProgramControls and Functions To install batteries in the remote control 3InstallationRemote Control Step Procedure For Details, refer to Quick SetupInstallation Overview Ambient Light Installation ConsiderationsWall-Mounting the DView Source Components Connections to the DViewHdmi Connections Rear of the Display Rear of the PC DVD/DTV STB Equipment Outputs to ExternalSpeakers Optional Connecting External10. Digital Audio Connection AmplifierRear Panel Connector Pin AssignmentsConnection Installation Changing the OSD Language Turning on the Power4Operation Setting the PC Display Properties Using the On-Screen Menus Timer Picture AdjustSetup SourceAspect Ratio Main MenuSource Control Description Aspect Ratio SettingsPicture Adjust Perform the adjustments in the order listed hereTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Audio Channel Timer Auto Adjust may take some time to complete, depending on SetupRating/Category Description FCC Ratings and Content CategoriesLetterbox Mode = Letterbox Operation Should be used by ISF-certified technicians only ISF Calibration100 DView Splash Screen Aspect Size Position PIPUsing Picture-In-Picture PIP HDMI1 HDMI2 Video Available Main and PIP Source CombinationsChanging the PIP Aspect Ratio Changing the PIP PositionChanging the PIP Size Images Audio Programs Swap button on the remote controlStereo Sound/SAP Broadcast Mode Receive Mode Mono StereoCompatibility with Stereo and SAP Audio Broadcasts Mono+SAPOperation Cleaning 5Maintenance and TroubleshootingTroubleshooting Tips Troubleshooting ChartComputer Signal RS-232 Connection and Port Configuration Serial Command SyntaxSerial Commands 6Serial CommunicationsS4E Command DescriptionSDB 0027 0024 Serial Communications DView Specifications 7SpecificationsSpecifications are subject to change without notice Weight Regulatory Approvals Limited WarrantyVL-40 Dimensions DView DimensionsView Signal Mode Vertical Frequency Horizontal Computer/Video Signal Compatibility ChartComputer Signal Compatibility Specifications Page Vidikron