Vidikron VL-37 manual 2Controls and Functions, DView at a Glance, Controls and Indicators

Page 15

2Controls and Functions

Figure 2-1and Figure 2-2show the locations of the DView controls, indicators and connectors.

Right Side

8

 

 

 

 

 

 

 

8

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5

6

7

1

2

3

4

2.1

DView at a Glance

Controls and Indicators

Figure 2-1. DView Controls and Indicators

1.TV/AV Button (Input Source Selection)

2.MENU Selection Button

3.Volume Adjustment Buttons

4.Channel Selection Buttons

5.Remote Control Sensor

6.Power Indicator

Lights red to indicate that the DView is in standby mode; lights green to indicate normal operation; flashes green when the DView receives a signal from the remote control.

7.Power Button

8.Speakers

Vidikron VL-37 Owner’s Operating Manual

5

Image 15
Contents VL-37HD High Definition Flat Panel LCD Monitor Page For LCD Displays ONE Year Limited WarrantyRIGHTS, Limits and Exclusions Vidikron DOC Compliance Notice Safety Precautions1Table of Contents Serial Communications Maintenance and TroubleshootingSpecifications Operation1List of Figures List of Figures About This Manual 1IntroductionIf you need Turn to Using This ManualKey Features and Benefits Description, Features and BenefitsOptional Accessories DView at a Glance Controls and IndicatorsPower Button Speakers 2Controls and FunctionsDVI/Computer Input Digital ConnectorsHeadphone Jack Main Power Switch Input 2 Audio Input Input 2 Composite Video InputInput 3 Component Video RCA connectors Input 3 Composite Video Input Input 3 Audio InputInput 1 Audio Input DView Remote Control DView Remote ControlNumeric Buttons Timer OFF ButtonMemory Preset Buttons OFF / onWide IntelliWide Aspect Ratio Selection Buttons ANA Anamorphic4X3 Standard Letbox Letterbox12. FC1/FC2/FC3/FC4 Sound Control ButtonsSurrnd Surround MTS/SAP Multichannel Television Sound/Second Audio ProgramControls and Functions Remote Control 3InstallationQuick Setup Installation OverviewStep Procedure For Details, refer to Installation Considerations Wall-Mounting the DViewAmbient Light Rear Connector Access Connections to the DViewSource Components DVI or Hdmi Source Connections Analog RGB Connections Input Monitor Output Connections RS-232 Control System Connection ConnectionInstallation Turning on the Power Changing the OSD Language Setting the PC Display Properties4Operation Using the On-Screen Menus Source Picture AdjustTimer SetupInput1 Input2 Input3 Input4 Main MenuSource Aspect RatioControl Description Aspect Ratio SettingsPerform the adjustments in the order listed here Picture AdjustTypical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Balance Equalizer Surround AudioTimer SetupTime On Timer Off Timer Sleep Timer Operation Rating/Category Description FCC Ratings and Content CategoriesPicture Adjust White Balance Blue Enable Gamma Baud Rate Command Ack Factory Reset Splash DurationISF Calibration Offset GainDView Splash Screen To use PIP, press the PIP Button Using Picture-In-Picture PIPAvailable Main and PIP Source Combinations Changing the PIP PositionMain Ratio ModeCalibration on Swapping the Main and PIP Audio Programs Swapping the Main and PIP ImagesMono+SAP Broadcast Mode Receive Mode Mono StereoStereo Sound/SAP Compatibility with Stereo and SAP Audio BroadcastsSymptom Possible Causes Solution 5Maintenance and TroubleshootingTroubleshooting Tips Troubleshooting ChartMaintenance and Troubleshooting Command Description Serial Command SyntaxRS-232 Connection and Port Configuration Serial CommandsSerial Communications OFF Enter 7Specifications DView SpecificationsSpecifications are subject to change without notice DView Dimensions DView DimensionsComputer/Video Signal Compatibility Computer/Video Signal Compatibility ChartSignal Type Mode Vertical Frequency Horizontal Specifications Page RUMA-011165