Vidikron VL-37 manual RS-232 Control System Connection

Page 31

Installation

Use a standard, 9-pin RS-232 cable to connect a PC or home theater control/automation

RS-232 Controller

system (if present) to the RS-232 port on the DView; see Figure 3-7.

Connection

For more information about using this connection, refer to Serial Communications on

 

page 47.

 

INPUT1MONITOR-OUT

Connector Pin Assignments:

2Receive Data

3Transmit Data

5

Ground

1, 4, 6, 7, 8, 9

Not Connected

Figure 3-7. RS-232 Control System Connection

Vidikron VL-37 Owner’s Operating Manual

21

Page 30 Page 32
Image 31
Page 30 Page 32
Contents VL-37HD High Definition Flat Panel LCD Monitor Page For LCD Displays ONE Year Limited WarrantyRIGHTS, Limits and Exclusions Vidikron DOC Compliance Notice Safety Precautions1Table of Contents Serial Communications Maintenance and TroubleshootingSpecifications Operation1List of Figures List of Figures About This Manual 1IntroductionIf you need Turn to Using This ManualKey Features and Benefits Description, Features and BenefitsOptional Accessories DView at a Glance Controls and IndicatorsPower Button Speakers 2Controls and FunctionsDVI/Computer Input Digital ConnectorsHeadphone Jack Main Power Switch Input 2 Audio Input Input 2 Composite Video InputInput 3 Composite Video Input Input 3 Audio Input Input 3 Component Video RCA connectorsInput 1 Audio Input DView Remote Control DView Remote ControlNumeric Buttons Timer OFF ButtonMemory Preset Buttons OFF / onWide IntelliWide Aspect Ratio Selection Buttons ANA Anamorphic4X3 Standard Letbox Letterbox12. FC1/FC2/FC3/FC4 Sound Control ButtonsSurrnd Surround MTS/SAP Multichannel Television Sound/Second Audio ProgramControls and Functions Remote Control 3InstallationInstallation Overview Quick SetupStep Procedure For Details, refer to Wall-Mounting the DView Installation ConsiderationsAmbient Light Connections to the DView Rear Connector AccessSource Components DVI or Hdmi Source Connections Analog RGB Connections Input Monitor Output Connections RS-232 Control System Connection ConnectionInstallation Changing the OSD Language Setting the PC Display Properties Turning on the Power4Operation Using the On-Screen Menus Source Picture AdjustTimer SetupInput1 Input2 Input3 Input4 Main MenuSource Aspect RatioControl Description Aspect Ratio SettingsPerform the adjustments in the order listed here Picture AdjustTypical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Balance Equalizer Surround AudioSetup TimerTime On Timer Off Timer Sleep Timer Operation Rating/Category Description FCC Ratings and Content CategoriesGamma Baud Rate Command Ack Factory Reset Splash Duration Picture Adjust White Balance Blue EnableISF Calibration Offset GainDView Splash Screen To use PIP, press the PIP Button Using Picture-In-Picture PIPChanging the PIP Position Available Main and PIP Source CombinationsMain Mode RatioCalibration on Swapping the Main and PIP Audio Programs Swapping the Main and PIP ImagesMono+SAP Broadcast Mode Receive Mode Mono StereoStereo Sound/SAP Compatibility with Stereo and SAP Audio BroadcastsSymptom Possible Causes Solution 5Maintenance and TroubleshootingTroubleshooting Tips Troubleshooting ChartMaintenance and Troubleshooting Command Description Serial Command SyntaxRS-232 Connection and Port Configuration Serial CommandsSerial Communications OFF Enter DView Specifications 7SpecificationsSpecifications are subject to change without notice DView Dimensions DView DimensionsComputer/Video Signal Compatibility Chart Computer/Video Signal CompatibilitySignal Type Mode Vertical Frequency Horizontal Specifications Page RUMA-011165
Top Page Image Contents