Vidikron VL-37 manual Sound Control Buttons, Surrnd Surround, 12. FC1/FC2/FC3/FC4

Page 21

Controls and Functions

11.Sound Control Buttons:

S.MODE

Press this button repeatedly to scroll through the available Equalizer presets (CUSTOM, STANDARD, MUSIC, FILM or SPEECH).

SURRND (Surround)

Press this button to turn Surround Mode on or off.

MTS/SAP (Multichannel Television Sound/Second Audio Program)

Press this button repeatedly to scroll through the available MTS settings (MONO, STEREO, SAP or Mono+SAP).

MUTE

Press this button to mute the audio output.

12.FC1/FC2/FC3/FC4

Not used with this model.

Vidikron VL-37 Owner’s Operating Manual

11

Image 21

Contents VL-37HD High Definition Flat Panel LCD Monitor Page For LCD Displays ONE Year Limited WarrantyRIGHTS, Limits and Exclusions Vidikron DOC Compliance Notice Safety Precautions1Table of Contents Specifications Maintenance and TroubleshootingOperation Serial Communications1List of Figures List of Figures About This Manual 1IntroductionIf you need Turn to Using This ManualKey Features and Benefits Description, Features and BenefitsOptional Accessories Power Button Speakers Controls and Indicators2Controls and Functions DView at a GlanceHeadphone Jack Main Power Switch ConnectorsInput 2 Audio Input Input 2 Composite Video Input DVI/Computer Input DigitalInput 3 Component Video RCA connectors Input 3 Composite Video Input Input 3 Audio InputInput 1 Audio Input DView Remote Control DView Remote ControlMemory Preset Buttons Timer OFF ButtonOFF / on Numeric Buttons4X3 Standard Aspect Ratio Selection Buttons ANA AnamorphicLetbox Letterbox Wide IntelliWideSurrnd Surround Sound Control ButtonsMTS/SAP Multichannel Television Sound/Second Audio Program 12. FC1/FC2/FC3/FC4Controls and Functions Remote Control 3InstallationQuick Setup Installation OverviewStep Procedure For Details, refer to Installation Considerations Wall-Mounting the DViewAmbient Light Rear Connector Access Connections to the DViewSource Components DVI or Hdmi Source Connections Analog RGB Connections Input Monitor Output Connections RS-232 Control System Connection ConnectionInstallation Turning on the Power Changing the OSD Language Setting the PC Display Properties4Operation Using the On-Screen Menus Timer Picture AdjustSetup SourceSource Main MenuAspect Ratio Input1 Input2 Input3 Input4Control Description Aspect Ratio SettingsPerform the adjustments in the order listed here Picture AdjustTypical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Balance Equalizer Surround AudioTimer SetupTime On Timer Off Timer Sleep Timer Operation Rating/Category Description FCC Ratings and Content CategoriesPicture Adjust White Balance Blue Enable Gamma Baud Rate Command Ack Factory Reset Splash DurationISF Calibration Offset GainDView Splash Screen To use PIP, press the PIP Button Using Picture-In-Picture PIPAvailable Main and PIP Source Combinations Changing the PIP PositionMain Ratio ModeCalibration on Swapping the Main and PIP Audio Programs Swapping the Main and PIP ImagesStereo Sound/SAP Broadcast Mode Receive Mode Mono StereoCompatibility with Stereo and SAP Audio Broadcasts Mono+SAPTroubleshooting Tips 5Maintenance and TroubleshootingTroubleshooting Chart Symptom Possible Causes SolutionMaintenance and Troubleshooting RS-232 Connection and Port Configuration Serial Command SyntaxSerial Commands Command DescriptionSerial Communications OFF Enter 7Specifications DView SpecificationsSpecifications are subject to change without notice DView Dimensions DView DimensionsComputer/Video Signal Compatibility Computer/Video Signal Compatibility ChartSignal Type Mode Vertical Frequency Horizontal Specifications Page RUMA-011165