![](/images/new-backgrounds/1273100/2731003x1.webp)
PREPARATION FOR USE
CONNECTIONS
Plug the incoming cable into the ANT jack on the rear of the TV.
Cable |
| Antenna | Rear of this TV | |
OR | ||||
TV signal | ||||
|
|
|
Incoming cable from home Antenna /
Cable Company (No Cable Box)
Cable Box or
Satellite Box*
OR
OUT
IN
ANT
Incoming cable from Cable
Company or Satellite Antenna *NOTE (DO NOT DISCONNECT FROM BOX) Some cable TV systems use scrambled signals
and require a special converter to receive these channels. Consult your local cable company.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
Note:
•For your safety and to avoid damages to the unit, unplug the antenna cable from the ANT jack before moving the unit.
[EXTERNAL CONNECTION]
INITIAL SETUP
When you turn on the power for the first time, the “SELECT LANGUAGE” menu is displayed.
The “INITIAL SETUP” menu is displayed every time you turn on the unit unless the scanning is completed.
1 Select the desired | SELECT LANGUAGE |
| 2 If the TV screen shows | - HELPFUL HINTS - | |
language according to |
|
|
| snow noise and there is | 1. PLEASE CHECK TO SEE IF THE |
ENGLISH | NEXT:PRESS CHK |
| PROPERLY CONNECTED. | ||
|
|
| ANTENNA/CABLE/SATELLITE IS | ||
the screen indication. | ESPAÑOL | DESPUÉS:PRESIONE CHL |
| no operation for more | 2. DID YOU PERFORM “AUTO PRESET CH” ? |
FRANÇAIS | APRÈS:PRESSEZ VOLX |
| OWNER’S MANUAL OR REAR PANEL FOR | ||
After that, the TV |
|
|
| than 5 seconds, | 3. PLEASE REFER TO FRONT PAGE OF THE |
|
|
| SUPPORT LINE INFORMATION. | ||
performs “AUTO |
|
|
| “HELPFUL HINTS” |
|
PRESET CH” to scan |
| – INITIAL SETUP – |
| appears. Follow the |
|
channels available for |
|
| instructions listed on- |
| |
PLEASE CONNECT ANTENNA OR CABLE |
|
| |||
the broadcasting in | OR SATELLITE TO THIS UNIT. |
| screen. |
| |
IN ORDER TO PERFORM |
|
| |||
| THEN PRESS CH K, |
|
|
| |
your area. | “AUTO PRESET CH ”. |
|
|
| |
|
|
|
|
| |
|
|
|
|
|
|
When the scanning is completed, or [MENU] is pressed during channel scanning to cancel it, the tuner stops on the lowest memorized channel.
Notes:
●In case no channel can be received by the channel scanning, “NO TV SIGNALS” is displayed on the screen. Turn off the unit and check the antenna connection, then follow step 1 again.
●If those settings do not work properly, please call our help line on the front page of this owner's manual.
SELECTING AUDIO/VIDEO INPUT
When you use the AUDIO/VIDEO input jacks, select “VIDEO1” or “VIDEO2” mode by pressing [INPUT SELECT] on the remote control or [INPUT SELECT] on the main unit. The input mode changes by pressing the button as following:
INPUT | TV channel | VIDEO1 | VIDEO2 |
SELECT |
TILT STAND
Tilt Stand | |
|
Adjust the stand to change the angle of TV
VIDEO1 input
(OUT)
ex.
(IN)
VIDEO2 |
R |
AUDIO |
L |
COMPONENT |
Y |
Pb |
Pr |
R |
AUDIO |
L |
Rear of this TV
OPERATIONS
REMOTE CONTROL AND TOP PANEL FUNCTION
| Audio Cable | ||
| (OUT) |
| |
| Video Cable | ||
Video Cassette | (OUT) | OR | |
Recorder | |||
| |||
|
| ||
|
(IN)
(IN)
VIDEO1 | |
| VIDEO |
| |
| ANT |
HEAD | PHONE |
|
IR transmitter |
|
|
To send infrared ray (IR) signal |
|
|
|
| INPUT |
|
| SELECT |
POWER button |
|
|
To turn TV on/off | POWER |
|
VOL X/Y buttons | o | CH |
m | p | |
To adjust volume | VOL n |
|
INPUT SELECT button
To select TV or external input
CH K/L buttons
To select channels and move up/down through menu items
Notes:
●The AUDIO L jack is for mono input. The sound is heard from both speakers. Use this jack for connecting monaural audio equipment.
●The
To decide the command of settings |
|
|
1 | 2 | 3 |
4 | 5 | 6 |
7 | 8 | 9 |
Channel number buttons
Press two digits to directly access the desired channel. Remember to press a "0" before a single digit channel.
+100 button
VIDEO2 input
ex.
(OUT)
Audio Cable
(IN)
(IN)
VIDEO2 |
R |
AUDIO |
L |
COMPONENT |
Y |
Pb |
Rear of this TV
MENU button | MENU | 0 | +100 | |
To view |
|
|
| |
MUTE button | MUTE | SLEEP | CH RET | |
To mute sound | ||||
|
|
| ||
DISPLAY button |
| DISPLAY |
| |
|
|
| ||
To display CH No./Audio Status |
|
|
|
Press to select cable channels higher than 99.
SLEEP button
To set Sleep Timer
CH RET button
To return to previous channel
Video Camera
| (OUT) | |
Video Game | Component | |
Video Cable | ||
|
| Pr |
| R |
AUDIO | |
| L |
VIDEO1 | |
| VIDEO |
| |
| ANT |
HEAD | PHONE |
Note:
●You can test if the remote control sends out the infrared signal with an AM radio. (Refer to “TROUBLESHOOTING GUIDE”.)
MENU button
To view
VOLUME K/L buttons
To adjust volume
CHANNEL K/L buttons
To select channels
INPUT SELECT button
To select TV or external input
POWER button
Notes:
●This TV can accept 480p / 480i / simplified 1080i video signal.
●Simplified 1080 video signal differs to the original 1080i video signal because it is displayed after converted into 480p signal.
INSTALLING THE BATTERIES |
| ||
1 | 2 | 3 | Install two AAA batteries (supplied) |
|
|
| matching the polarity indicated inside |
|
|
| battery compartment of the remote con- |
|
|
| trol. |
[BATTERY PRECAUTIONS]
•Be sure to follow the correct polarity as indicated in the battery compartment. Reversed batteries may cause damage to the device.
•Do not mix different types of batteries together (e.g. Alkaline and
•If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from possible battery leakage.
•Do not try to recharge batteries not intended to be recharged; they can overheat and rupture.
To turn TV on/off
MENU | VOLUME | CHANNEL | INPUT SELECT | POWER |
Power Indicator
Infrared Sensor Window
Note:
●If some digits appear in the corner of the screen when the unit is turned on at the first time, press [POWER] without unplugging the power cord.