Runco VX-44D, VX-55D manual HD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV

Page 88

HD Format

HD/RGB 1

Auto

HD/RGB 2

Auto

ADC Bandwidth

Auto

YPbPr Input Resolution

HD Format: If the characteristics of the incoming signal on the HD1 or HD2 inputs are known, select HD Format from the Service menu and set them as described below. Doing so can reduce the time it takes the DHD Controller to switch from HD to 480i signals or vice versa.

This is generally not necessary unless the DHD Controller – for whatever reason – has difficulty determining the color space (RGB or YUV), bandwidth or resolution of the incoming HD signal. In most situations, the Auto settings work well.

HD/RGB 1 and HD/RGB 2 (Color Space): Select Auto, RGB or YUV.

ADC Bandwidth: Select Auto, 75 MHz, 150 MHz or 300 MHz.

YPbPr Input Resolution: Select Auto or specify the input resolution, if known: 480i, 480p, 576i, 576p, 720p or 1080i.

Triggers: Select Triggers from the Service menu to configure the 12-volt trigger outputs. You can assign one or more trigger outputs to each aspect ratio. Those triggers are then activated by selecting that aspect ratio.

If your projector is equipped with the Runco CineWide with AutoScope system, assign at least one trigger output (the same one to which the lens motor is connected) to the Cinema and Virtual Cinema aspect ratios.

To configure a trigger to activate when the system is turned on –

Tip for example, when using the trigger to control a retractable screen

– assign that trigger to all aspect ratios.

To save the trigger settings so that they can be restored after a System Reset (described below), press repeatedly to highlight “Save.” Then, press ENTER.

Miscellaneous: Select Miscellaneous from the Service menu to set the following options:

Language: Select Language from the Miscellaneous menu and press the up- or down-arrows to select the OSD language. (Currently, only English is supported.)

Menu Mode: This is the manner in which the OSD menus appear and disappear when you press MENU. Choose one of the following:

0 = No transition; menus abruptly appear and disappear.

1 = Menus fade in and out.

2 = “Checkerboard” dissolve; menus appear and disappear in sections.

3 = “Window shade” effect; menus are drawn on a diagonal from top left to bottom right, and retract in the opposite direction.

Timeout - Short/Long: These settings control how long the OSD menus stay on screen. Select a time-out period of from 2 to 60 seconds.

76

Runco VX-44d/-55d Owner’s Operating Manual

Image 88
Contents VX-44d VX-55d Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Runco INTERNATIONAL, INC Safety Precautions Table of Contents Install Projector Stand CineWide with AutoScope, Floor-Mount Maintenance and Troubleshooting SpecificationsOperation Serial CommunicationsTable of Contents List of Figures Xii About This Manual Using This Manual Certain featuresSignificance. They also provide supplemental information Degrade performance or cause a malfunctionDescription, Features and Benefits Format screenOptional Accessories VX-44d/-55d at a Glance VX-44d/-55d Top/Rear/Front ViewVX-44d/-55d Input Panel Ethernet RemoteInput 1 Rgbhv VX-44d/-55d Rear-Panel Keypad UP Button Left ButtonDown Button Right ButtonDHD Controller Front Panel Runco IconIR Sensor Vacuum Fluorescent DisplayMenu Button Outputs 1. Hdmi OUT DHD Controller Rear PanelComposite Video Input Main Power Switch RS-232 OutputRS-232 Control Port Main AC FuseVX-44d/-55d Remote Control Unit DHD Controller/VX-44d/-55d Remote ControlEnter IR Output IndicatorLight Cinema ISF NightISF DAY CustInstallation Remote ControlQuick Setup Installation OverviewInstallation specialist Step Procedure For Details, Refer toInstallation Considerations Projector Installation OptionsInstallation Type Ambient LightVX-44d/-55d Lens Options and Throw Ratios Ceiling Installation Floor InstallationVertical and Horizontal PositionHorizontal Lens Shift Example only Vertical and Horizontal Lens Shift Limits Folded Optics Installing the Projection Lens Lens Assembly Front ViewAutoScope or Base Plate Installing the Optional CineWide Lens MountFixed CineWide Are both fully assembled AutoScope stand used for floor-mounted projector Mounting VX-44d/-55dConnecting the VX-44d/-55d to the DHD Controller Connections to VX-44d/-55d and DHD ControllerConnecting Source Components to the DHDController Hdmi Connections See FigureDigital DTV RGB or Component Video Connections See Figure 10. Digital DTV RGB or Component Video ConnectionsAnalog Computer RGB Connections See Figure Personal ComputerComposite/S-Video/Component Video Connections See Figure DVD Player, VCR Satellite Receiver Laser Disc etcConnecting 12-Volt RS-232 ControllerConnection Trigger Outputs to14. Connecting 12-Volt Trigger Outputs Connecting an External IR Receiver to the DHD ControllerBuilt-in IR sensor on the DHD Controller is disabled Input voltage to the AutoScope lens motor must be betweenTurning on the Power Component SD Ntsc 480i 169Vx44/55Adjusting the Picture Orientation Primary Lens Adjustments Focus Zoom Vertical and Horizontal Lens ShiftInstalling and Adjusting the CineWide Anamorphic Lens It is extremely important that the primary lens is properlyConfigure Lens Motor Adjust the AnamorphicHorizontal Position X Adjustment Trigger CineWide withInstallation Anamorphic Lens Top View GeometryWrong Position Calibrating Projector Input 2 DVI 16. TheaterMaster Remote Control for VX-44d/-55d MainTheaterMaster Remote Control FunctionsChannel Setup Are disabledNavigating the Projector Menus PDig IDig4x3 nt Lbx ntAuto Setup Channel Edit NameAnamorphic lens in the light path, the aspect ratio is Size and Position MenuTechnical Support Installation Adjust Pixel Tracking before Pixel Phase Values shown represent where the approximate centerPicture Quality Menu Recommended see belowBack Porch There must be at least two consecutive white pixels present Uncheck this item before exiting this menu256 Auto Color Enable Clipping Detector Color Enable RedWhite Balance Pre Calibration 256Installation Menu Readjust when absolutely necessaryTo using LumaCal LumaCal lamp calibration takes approximately two minutesPower cycles Working With the Lamp Originally expected may no longer be possibleIntensity value is not the actual lumen output, but rather a More easily maintained as the lamp ages Using the On-Screen Menus OperationISF Presets ServiceInput Source Aspect RatioInput Source Main MenuAspect Ratio Aspect Ratio Settings Remote Aspect Ratio Control Description KeyCinema Picture Picture Brightness Contrast Color Tint SharpnessTypical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position ResolutionInput Position Left/Right Up/Down Width Height Overscan ISF Presets ISF Presets ISF Night ISF Day Custom Save Factory DefaultInformation Information Serial Number Hardware Firmware 0100.023A DateCalibration You must enter a passcode to access the Calibration menuShould be used by ISF-certified technicians only Operation You must enter a passcode to access the Service menu ServiceInput Names Restore Composite Video Component SD Do not change the Type setting in this menu Vertical Keystone CorrectionHD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV ADC Bandwidth Auto YPbPr Input ResolutionAuto Operation Operation Lamp and Filter Replacement Removing the Lamp DoorRemoving the Lamp Lamp Message Lamp Limit Lamp Mode Power Intensity 147Lamp S/N RVRLens Replacement Removing the Primary LensTroubleshooting Chart Troubleshooting TipsSymptom Possible Causes Solution Configure Lens Motor Error Codes VX-44d/-55d Error CodesCode Description General Power and Cooling Code Description Lamp FailuresBuilt-In Keypad Code Description Tipm Image ProcessorPanel Driver and Formatter Code Description Miscellaneous Serial Command Syntax RS-232 Connection and Port ConfigurationSerial Commands Aspect Ratio Commands Image Preset Commands Output Shift Commands Bkgnd Command Parameter Value Min/max Enter keyVX-44d/-55d Specifications VX-44d/-55d SpecificationsHome Theater Calibration Specifications Industry-Standard SpecificationsPower Requirements VX-44d DimensionsLimited Warranty Specifications are subject to change without noticeDHD Controller Specifications DHD Controller SpecificationsVX-44d/-55d Dimensions VX-44d/-55d Dimensions100 Runco VX-44d/-55d Owner’s Operating Manual Page RUMA-011195 Rev 02-01-07 Runco CL-810 Owner’s Operating Manual
Related manuals
Manual 120 pages 41.71 Kb

VX-55D, VX-44D specifications

The Runco VX-55D and VX-44D projectors represent a pinnacle in home theater technology, offering expansive image quality and immersive viewing experiences. Runco, known for its commitment to delivering exceptional visual performance, has integrated numerous features and advanced technologies in these models.

One of the standout features of both the VX-55D and VX-44D is their native 1080p resolution, delivering stunningly sharp images with vibrant colors that capture the finest details. This high definition capability ensures that viewers can enjoy their favorite movies, sports, and gaming content with unparalleled clarity. The projectors utilize the latest DLP (Digital Light Processing) technology, which enhances brightness and color accuracy, providing a more vivid and lifelike picture.

Another impressive characteristic of the Runco VX series is its exceptional contrast ratios. With deep blacks and brilliant whites, these projectors offer a dynamic range that brings out subtle details in both shadow and highlight areas. This contrast performance is particularly beneficial for watching films in darker environments, where the depth of imagery is crucial for immersion.

In terms of color processing, the VX-55D and VX-44D incorporate Runco's proprietary ColorPalette technology. This system ensures accurate and rich color reproduction by utilizing a wide color gamut, allowing viewers to experience content as the creators intended. Coupled with advanced color management capabilities, users can further tweak their viewing experience to match their preferences.

The integration of flexible installation options is another highlight of these projectors. They support up to 10-point digital keystone correction, making setup simple and adaptable to various room configurations. This flexibility ensures that no matter the space, users can achieve a perfectly aligned and geometrically accurate image.

Runco has also designed the VX-55D and VX-44D with user-friendly interfaces, including intuitive remote controls and on-screen menus. Both projectors come equipped with multiple HDMI inputs, allowing users to connect various devices seamlessly. Additionally, they support 3D content playback, a feature that has become increasingly important for enhancing the cinematic experience.

Energy efficiency is a consideration in the design of these projectors as well, making them not only high-performance devices but also more sustainable than many of their counterparts. With a sleek aesthetic, the Runco VX-55D and VX-44D can seamlessly blend into any home theater setup, adding a touch of elegance while providing an extraordinary viewing experience.

In summary, the Runco VX-55D and VX-44D projectors are characterized by their high-definition resolution, advanced DLP technology, rich color processing, and flexible installation options, making them ideal choices for any home theater enthusiast looking to elevate their viewing experience.