Runco VX-55D 147, Lamp S/N, Lamp Message Lamp Limit Lamp Mode Power Intensity, Rvr, Change Lamp

Page 93

Maintenance and Troubleshooting

13.Press ENTER to accept the change. This adds the new lamp serial number to the Lamp History menu and resets the Lamp Hours timer to “0.” Lamp Mode and Lamp Limit remain as they were for the previous lamp and can be changed at any time.

Lamp Adjust

Lamp Hours

147

Lamp S/N

123456789

1. Lamp Message

2.Lamp Limit 1000

3. Lamp Mode Power

4.Power 500

5.

Intensity

0

6.

RVR

3

7.

Lamp History

 

8.Change Lamp

9. Reserved

Figure 5-5. Recording the Serial Number of a New Lamp

Always record the serial number of a new lamp. Do this only if you

Note have just installed a new lamp. This will ensure that the lamp timer is not reset on an old lamp and that the number of hours logged on the lamp is accurate.

Whenever you replace the lamp – or more often if the projector is installed in an extremely Filter Replacement

dusty environment – you should also replace the two filters located at the front and right

side of the projector.

 

1. Loosen the six screws holding right side filter access

Side Filter Access Cover

panel in place. Then, remove the panel.

 

2. Loosen the two screws holding front filter access

Front Filter Access Cover

panel in place. Then, remove the panel.

 

3.Pull the filters out of the projector and discard. Do not reuse filters.

4.Insert the new filters with the wired side in.

5.Replace the filter access panels and tighten the screws to secure them.

Runco VX-44d/-55d Owner’s Operating Manual

81

Page 92 Page 94
Image 93
Page 92 Page 94
Contents VX-44d VX-55d Page For Projectors, Video Processors and Controllers TWO Year Limited WarrantyEffective Warranty Date Runco INTERNATIONAL, INC Safety Precautions Table of Contents Install Projector Stand CineWide with AutoScope, Floor-Mount Specifications Maintenance and TroubleshootingOperation Serial CommunicationsTable of Contents List of Figures Xii About This Manual Certain features Using This ManualSignificance. They also provide supplemental information Degrade performance or cause a malfunctionFormat screen Description, Features and BenefitsOptional Accessories VX-44d/-55d Top/Rear/Front View VX-44d/-55d at a GlanceVX-44d/-55d Input Panel Remote EthernetInput 1 Rgbhv VX-44d/-55d Rear-Panel Keypad Left Button UP ButtonDown Button Right ButtonRunco Icon DHD Controller Front PanelIR Sensor Vacuum Fluorescent DisplayMenu Button DHD Controller Rear Panel Outputs 1. Hdmi OUTComposite Video Input RS-232 Output Main Power SwitchRS-232 Control Port Main AC FuseDHD Controller/VX-44d/-55d Remote Control VX-44d/-55d Remote Control UnitIR Output Indicator EnterLight ISF Night CinemaISF DAY CustRemote Control InstallationInstallation Overview Quick SetupInstallation specialist Step Procedure For Details, Refer toProjector Installation Options Installation ConsiderationsInstallation Type Ambient LightVX-44d/-55d Lens Options and Throw Ratios Floor Installation Ceiling InstallationVertical and Horizontal PositionHorizontal Lens Shift Example only Vertical and Horizontal Lens Shift Limits Folded Optics Lens Assembly Front View Installing the Projection LensInstalling the Optional CineWide Lens Mount AutoScope or Base PlateFixed CineWide Are both fully assembled AutoScope stand used for floor-mounted projector VX-44d/-55d MountingConnections to VX-44d/-55d and DHD Controller Connecting the VX-44d/-55d to the DHD ControllerComponents to the DHD Connecting SourceController Hdmi Connections See Figure10. Digital DTV RGB or Component Video Connections Digital DTV RGB or Component Video Connections See FigurePersonal Computer Analog Computer RGB Connections See FigureDVD Player, VCR Satellite Receiver Laser Disc etc Composite/S-Video/Component Video Connections See FigureRS-232 Controller Connecting 12-VoltConnection Trigger Outputs toConnecting an External IR Receiver to the DHD Controller 14. Connecting 12-Volt Trigger OutputsInput voltage to the AutoScope lens motor must be between Built-in IR sensor on the DHD Controller is disabledComponent SD Ntsc 480i 169Vx44/55 Turning on the PowerFocus Zoom Vertical and Horizontal Lens Shift Adjusting the Picture Orientation Primary Lens AdjustmentsIt is extremely important that the primary lens is properly Installing and Adjusting the CineWide Anamorphic LensAdjust the Anamorphic Configure Lens MotorHorizontal Position X Adjustment Trigger CineWide withInstallation Geometry Anamorphic Lens Top ViewWrong Position Calibrating Projector Input 2 DVI Main 16. TheaterMaster Remote Control for VX-44d/-55dControl Functions TheaterMaster RemoteAre disabled Channel SetupNavigating the Projector Menus IDig PDig4x3 nt Lbx ntChannel Edit Name Auto SetupSize and Position Menu Anamorphic lens in the light path, the aspect ratio isTechnical Support Installation Values shown represent where the approximate center Adjust Pixel Tracking before Pixel PhasePicture Quality Menu Recommended see belowBack Porch Uncheck this item before exiting this menu There must be at least two consecutive white pixels presentClipping Detector Color Enable Red 256 Auto Color EnableWhite Balance Pre Calibration 256Readjust when absolutely necessary Installation MenuTo using LumaCal LumaCal lamp calibration takes approximately two minutesPower cycles Originally expected may no longer be possible Working With the LampIntensity value is not the actual lumen output, but rather a More easily maintained as the lamp ages Operation Using the On-Screen MenusService ISF PresetsInput Source Aspect RatioMain Menu Input SourceAspect Ratio Remote Aspect Ratio Control Description Key Aspect Ratio SettingsCinema Picture Brightness Contrast Color Tint Sharpness PictureTypical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Resolution Input PositionInput Position Left/Right Up/Down Width Height Overscan ISF Presets ISF Night ISF Day Custom Save Factory Default ISF PresetsInformation Information Serial Number Hardware Firmware 0100.023A DateYou must enter a passcode to access the Calibration menu CalibrationShould be used by ISF-certified technicians only Operation Service You must enter a passcode to access the Service menuInput Names Restore Composite Video Component SD Vertical Keystone Correction Do not change the Type setting in this menuADC Bandwidth Auto YPbPr Input Resolution HD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUVAuto Operation Operation Removing the Lamp Door Lamp and Filter ReplacementRemoving the Lamp 147 Lamp Message Lamp Limit Lamp Mode Power IntensityLamp S/N RVRRemoving the Primary Lens Lens ReplacementTroubleshooting Tips Troubleshooting ChartSymptom Possible Causes Solution Configure Lens Motor VX-44d/-55d Error Codes Error CodesCode Description General Code Description Lamp Failures Power and CoolingCode Description Tipm Image Processor Built-In KeypadPanel Driver and Formatter Code Description Miscellaneous RS-232 Connection and Port Configuration Serial Command SyntaxSerial Commands Aspect Ratio Commands Image Preset Commands Output Shift Commands Bkgnd Enter key Command Parameter Value Min/maxVX-44d/-55d Specifications VX-44d/-55d SpecificationsIndustry-Standard Specifications Home Theater Calibration SpecificationsPower Requirements VX-44d DimensionsSpecifications are subject to change without notice Limited WarrantyDHD Controller Specifications DHD Controller SpecificationsVX-44d/-55d Dimensions VX-44d/-55d Dimensions100 Runco VX-44d/-55d Owner’s Operating Manual Page Runco CL-810 Owner’s Operating Manual RUMA-011195 Rev 02-01-07
Related manuals
Manual 120 pages 41.71 Kb

VX-55D, VX-44D specifications

The Runco VX-55D and VX-44D projectors represent a pinnacle in home theater technology, offering expansive image quality and immersive viewing experiences. Runco, known for its commitment to delivering exceptional visual performance, has integrated numerous features and advanced technologies in these models.

One of the standout features of both the VX-55D and VX-44D is their native 1080p resolution, delivering stunningly sharp images with vibrant colors that capture the finest details. This high definition capability ensures that viewers can enjoy their favorite movies, sports, and gaming content with unparalleled clarity. The projectors utilize the latest DLP (Digital Light Processing) technology, which enhances brightness and color accuracy, providing a more vivid and lifelike picture.

Another impressive characteristic of the Runco VX series is its exceptional contrast ratios. With deep blacks and brilliant whites, these projectors offer a dynamic range that brings out subtle details in both shadow and highlight areas. This contrast performance is particularly beneficial for watching films in darker environments, where the depth of imagery is crucial for immersion.

In terms of color processing, the VX-55D and VX-44D incorporate Runco's proprietary ColorPalette technology. This system ensures accurate and rich color reproduction by utilizing a wide color gamut, allowing viewers to experience content as the creators intended. Coupled with advanced color management capabilities, users can further tweak their viewing experience to match their preferences.

The integration of flexible installation options is another highlight of these projectors. They support up to 10-point digital keystone correction, making setup simple and adaptable to various room configurations. This flexibility ensures that no matter the space, users can achieve a perfectly aligned and geometrically accurate image.

Runco has also designed the VX-55D and VX-44D with user-friendly interfaces, including intuitive remote controls and on-screen menus. Both projectors come equipped with multiple HDMI inputs, allowing users to connect various devices seamlessly. Additionally, they support 3D content playback, a feature that has become increasingly important for enhancing the cinematic experience.

Energy efficiency is a consideration in the design of these projectors as well, making them not only high-performance devices but also more sustainable than many of their counterparts. With a sleek aesthetic, the Runco VX-55D and VX-44D can seamlessly blend into any home theater setup, adding a touch of elegance while providing an extraordinary viewing experience.

In summary, the Runco VX-55D and VX-44D projectors are characterized by their high-definition resolution, advanced DLP technology, rich color processing, and flexible installation options, making them ideal choices for any home theater enthusiast looking to elevate their viewing experience.
Top Page Image Contents