Runco SP-60DHD / SP-60DHDXA manual Maintenance and Troubleshooting, Cleaning the Screen

Page 59

5. Maintenance and Troubleshooting

Regular cleaning will extend the life and performance of the PlasmaWall. Before cleaning, be sure to unplug the power cord from the power outlet.

Do not under any circumstances use solvents such as benzene or thinner to clean the PlasmaWall. Doing so may cause deterioration or peeling of paint from the display or remote control unit.

Wipe the display and remote control gently with a soft cloth. In the case of excessive dirt buildup, dampen a soft cloth with a diluted neutral cleaning detergent and after wringing the cloth thoroughly, wipe the component and then dry it with a dry soft cloth.

5.1 Cleaning

Cleaning the Display

Panel Body and Remote

Control

After dusting, wipe the screen gently using the supplied cleaning cloth or another soft	Cleaning the Screen
cloth (cotton, flannel etc.). Do not use tissue or a rough cloth. The screen surface is easily
scratched; do not rub it or hit it with a hard object.
If you clean the surface of the screen with a wet cloth, water droplets on the surface may
enter into the product and cause a malfunction.
As a general rule, use a vacuum cleaner about once a month to clean the vents on the	Cleaning the Vents
rear panel of the display of dust buildup (set the vacuum cleaner to its weakest setting
when doing this). If not removed, accumulated dust can cause the internal temperature to
increase, resulting in possible breakdown or fire.

PlasmaWall SP Series Owner’s Operating Manual

49

Image 59

Contents OW N E R ’S OP E R a T I N G MA N U a L Page For Plasma Displays Three Year Limited WarrantyRIGHTS, Limits and Exclusions Runco INTERNATIONAL, INC Safety Precautions Table of Contents Operation Maintenance and TroubleshootingSpecifications Appendix A. PlasmaWall Service Remote ControlList of Figures List of Figures About This Manual IntroductionIf you need Turn to Using This ManualKey Features and Benefits Description, Features and BenefitsOptional Accessories PlasmaWall at a Glance Controls and IndicatorsControls and Functions PlasmaWall Model SP-42DHD Rear Panel PlasmaWall Model SP-50DHD Rear Panel PlasmaWall Model SP-60DHD Rear Panel External Speaker Output Left Main Power SwitchDigital RGB Input 2 DVI-D External Speaker Output RightIR Sensor Power ButtonDHD Controller Front Panel Runco IconDown Button UP ButtonLeft Button Enter ButtonInputs 3. DVI 1 / DVI 2 Digital Component Video RCA connectorsDHD Controller Rear Panel DVI OUTMain AC Fuse Composite Video InputRS-232 Control Port DHD Controller Remote Control DHD Controller Remote ControlMenu IR Output IndicatorEnter LightISF DAY CinemaSVC ISF NightRemote Control InstallationOther surfaces Step Procedure For Details, refer to Quick SetupMounting the PlasmaWall InstallationConsiderations High-Altitude OperationVentilation Ambient LightInstallation Connections to the PlasmaWall and DHD Controller Connecting PlasmaWall to the DHD ControllerRS-232 Connection from the DHD Controller to the PlasmaWall DVI Source DVD Player or HD Tuner with Hdmi or DVI out Connecting SourceComponents to the DHD DVI Connections See FigureDigital DTV RGB Connections Digital DTV RGB Connections SeePersonal Computer Refer to Computer/Video Signal Compatibility on page 64 forAnalog Computer RGB Connections See Figure DVD Player, VCR Satellite Receiver Laser Disc etc Composite/S-Video/Component Video Connections See FigureConnection Connecting 12-Volt Trigger Outputs to External EquipmentRS-232 Controller 11. Installing the Cable Ties Operation Turning on the PowerYou must enter a passcode to access the Service menu Operation Using the On-Screen Menus Aspect Ratio ISF PresetsService Input SourceHD Pass Thru 1 HD Pass Thru Main MenuInput Source Aspect RatioRemote Aspect Ratio Control Description Key Aspect Ratio SettingsPicture Brightness Contrast Color Tint Sharpness PictureTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Input Position Left/Right Up/Down Width Height Overscan Input PositionSerial Number Hardware Firmware 0002.034B Date Nov 25 ISF PresetsISF Presets ISF Night ISF Day Custom Save Factory Default InformationCalibration Gain/Offset Refer to ISF Night Display Color, aboveOperation Service HD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV Do not change the Type setting in this menuOperation Operation Cleaning the Screen Maintenance and TroubleshootingCleaning Cleaning the Display Panel Body and Remote ControlSymptom Possible Causes Solution Troubleshooting TipsComputer/Video Signal Maintenance and Troubleshooting Letterbox Enter Serial CommunicationsAspect Ratio Commands CommandValue Description Min/max Stored? Power On/Off Commands Input Selection CommandsImage Preset Commands Output Shift Commands Value Description Min/max Stored? Input Position CommandsBkgnd Enter key Command Parameter min/max Value Stored? DescriptionModel SP-50DHD SpecificationsPlasmaWall Specifications Model SP-42DHDDHD Controller Specifications PlasmaWall Dimensions14.8 34.3 49.1 M8 Screw KHz Computer/Video Signal CompatibilityInput Refresh Rate Resolution Remarks Horiz56.0 45.1 Specifications Overview Figure A-1. PlasmaWall Service Remote ControlDVI-D RGB SetupAspect Ratio RGB-HDReduction Service/Setup MenuVideo NR Noise PlasmaWall Service Remote Control Page Runco CL-810 Owner’s Operating Manual