Runco PL-61DHD, PL-50XA manual Operation

Page 50

Operation

ISF Night - Display Color: Use the Display Color settings to change the characteristics of the output signal. These settings are global (independent of any particular input).

Gain: Use the Gain controls to correct color imbalances in the bright areas of the image. A good way to do this is to use a test pattern consisting mostly of solid white areas, such as an 80 IRE “window” pattern. If the white areas contain traces of red, green or blue, decrease the Gain for that color.

Offset: Use the Offset controls in the White Balance sub-menu to correct color imbalances in the dark areas of the image. A good way to do this is to use a test pattern consisting mostly of dark gray areas, such as a 30 IRE “window” pattern. If the gray areas contain traces of red, green or blue, decrease the Offset for that color.

ISF Night - Input Image: The Input Image controls are similar to those in the Picture menu, but are accessible only by entering the Calibration menu passcode. This makes it possible to restore the picture quality settings to what they were when the display was installed, simply by recalling the “ISF Night” preset.

ISF Night - Input Color: The Input Color controls are similar to those in the Display Color menu (see above), but can be set independently for each input.

Gain/Offset: Refer to ISF Night - Display Color, above.

Chroma Delay: use the Chroma Delay control to correct a mis-aligned image from a Composite, S-Video or Component video source. Chroma delay in an image causes color shifts to occur to the left of the vertical edge transitions, producing artificial shadows or a “halo” effect. If necessary, adjust this setting to eliminate them.

Phase: Adjust the phase if the image (usually from an RGB source) shows shimmer or “noise.” Pixel phase adjusts the phase of the pixel sampling clock relative to the incoming signal. The effect of this control is similar to that of a tracking control on a VCR.

For best results, use a good test pattern such as a smooth gray consisting of a clear pattern of black and white pixels, or a similar “half on, half off” graphic image. (You may notice that you can stabilize the image at more than one point. Use either setting in this case.)

Noise Reduction: To apply Digital Noise Reduction (DNR) to the input signal, select Noise Reduction from the Input Color menu. Noise reduction is useful for clearing up noisy images from 480i video sources.

Use the left- or right-arrow buttons to select the desired amount of noise reduction, keeping in mind that higher settings (which reduce high frequencies) may also “soften” the image.

ISF Day - Display Color: Refer to ISF Night - Display Color.

ISF Day - Input Image: Refer to ISF Night - Input Image.

ISF Day - Input Color: Refer to ISF Night - Input Color.

Output Shift: The controls in the Output Shift menu are similar to those in the Input Position menu, except that they change the characteristics of the output signal (so the change is visible no matter which input is selected).

40

Runco PlasmaWall Owner’s Operating Manual

Image 50
Contents PL-50XA PL-61DHD Page Three Year Limited Warranty For Plasma DisplaysRIGHTS, Limits and Exclusions Runco INTERNATIONAL, INC Safety Precautions DOC Compliance NoticeTable of Contents Operation Maintenance and TroubleshootingSpecifications Serial CommunicationsList of Figures List of Figures Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Key Features and BenefitsOptional Accessories PlasmaWall at a Glance Controls and IndicatorsControls and Functions MENU/ENTER ConnectorsInput SELECT/EXIT DVD/HD2 External Speaker OutputsAUDIO1, AUDIO2, AUDIO3 DVD/HD3, DVD/HD4 HdmiIR Sensor DHD Controller Front PanelRunco Icon Vacuum Fluorescent DisplayEnter Button UP ButtonLeft Button Down ButtonDHD Controller Rear Panel HD1 / HD2 Analog BNC connectorsComponent Video RCA connectors DVI OUTRS-232 Control Port Main Power SwitchComposite Video Input Main AC FuseDHD Controller Remote Control DHD Controller Remote ControlLight IR Output IndicatorEnter MenuISF DAY CinemaSVC CustInstallation Remote ControlOther surfaces Quick Setup Step Procedure For Details, refer toMounting the PlasmaWall InstallationConsiderations On a Wall or Table StandProlong operating life VentilationOther Considerations DHD Controller Connecting PlasmaWall to the DHD ControllerConnections to the PlasmaWall and DHD Controller RS-232 Connection from the DHD Controller to the PlasmaWall Connecting Source DTV Source Refer to Computer/Video Signal Compatibility on page 55 for Analog Computer RGB Connections See FigureComposite/S-Video/Component Video Connections See Figure Composite, S-Video and Component Video ConnectionsRS-232 Controller Connection11. Installing the Cable Clamps Cable ManagementInstallation Turning on the Power OperationSetting the PC Display Properties Changing the OSD LanguageUsing the On-Screen Menus Input Source ISF PresetsService Aspect RatioAspect Ratio Main MenuInput Source Input Source Composite Video 1 S-Video Component SDAspect Ratio Settings Remote Aspect Ratio Control Description KeyPicture Picture Brightness Contrast Color Tint SharpnessTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Input Position Input Position Left/Right Up/Down Width Height OverscanInformation ISF PresetsISF Presets ISF Night ISF Day Custom Save Factory Default CalibrationOperation Service Operation Operation Operation Symptom Possible Causes Solution Maintenance and TroubleshootingTroubleshooting Tips Computer/Video Signal Command Parameter Value Description Min/max Stored? Serial CommunicationsSerial Communications Tint OWIDTH? Specifications are subject to change without notice SpecificationsPlasmaWall Specifications End user except for plasma glass panelDHD Controller Specifications PlasmaWall Dimensions PlasmaWall Model PL-50XA DimensionsPlasmaWall Model PL-61DHD Dimensions Computer/Video Signal Compatibility Computer/Video Signal Compatibility ChartSUN Page RUMA-010950
Related manuals
Manual 68 pages 9.96 Kb Manual 72 pages 63.77 Kb

PL-50XA, PL-61DHD specifications

The Runco PL-61DHD is a premium plasma television that has captured the attention of home theater enthusiasts since its introduction. With a striking 61-inch display, this model combines advanced technology with elegant design to create a stunning viewing experience.

One of the standout features of the PL-61DHD is its impressive picture quality. The television boasts a full HD resolution of 1920 x 1080 pixels, which ensures that every image is sharp and vibrant. This high resolution, combined with Runco's proprietary video processing technology, delivers exceptional color accuracy and contrast, making it suitable for a range of content from movies to sports broadcasts.

The PL-61DHD employs Runco's unique Color Fidelity technology, which enhances the precision of colors on the screen. This technology ensures that viewers experience shades that are true to life, which significantly elevates the overall viewing experience. Moreover, the plasma panel excels in black levels and contrast ratios, providing deep blacks and bright highlights that make images pop.

Another impressive feature of the PL-61DHD is its ambient light rejection capability. This allows the television to perform remarkably well in various lighting conditions, making it versatile for different room environments. Whether in a dimly lit theater room or a bright living space, the PL-61DHD adapts to deliver optimal performance.

To facilitate seamless connectivity, the Runco PL-61DHD includes multiple input options, such as HDMI and component video. This range of connections allows users to hook up various devices, including Blu-ray players, gaming consoles, and streaming devices, maximizing the television's usability and making it a central hub for home entertainment.

The build quality of the PL-61DHD reflects Runco's commitment to excellence. The sleek and stylish design not only enhances the aesthetics of any room but is also engineered for durability. The unit’s robust construction ensures longevity, making it a solid investment for avid home theater enthusiasts.

In conclusion, the Runco PL-61DHD stands out in the world of high-end televisions due to its unparalleled picture quality, advanced technology features, and stylish design. It is a definitive choice for anyone looking to elevate their home viewing experience, making it a timeless addition to any home theater setup.