Runco CX-52HD, CX-57HD manual Using This Manual, If you need Turn to

Page 14

Introduction

1.2

Using This Manual

Graphic Conventions: These symbols appear in numerous places throughout the manual, to emphasize points that you must keep in mind to avoid problems with your equipment or injury:

Tip

TIPS highlight time-saving short cuts and helpful guidelines for using

certain features.

Note

NOTES emphasize text with unusual importance or special

significance. They also provide supplemental information.

Caution

CAUTIONS alert users that a given action or omitted action can

degrade performance or cause a malfunction.

 

WARNING

WARNINGS appear when a given action or omitted action can result

in damage to the equipment, or possible non-fatal injury to the user.

DANGER!

DANGER appears when a given action can cause severe injury or

death.

 

Use the following table to locate the specific information you need in this manual.

If you need...

... Turn to page:

 

 

Information about obtaining service

iv

 

 

General information about the CX-52HD and

3

CX-57HD Flat-Panel LCDs

 

 

 

Installation instructions

13

 

 

First-time configuration instructions

23

 

 

Advanced configuration instructions

40

 

 

Troubleshooting tips

49

 

 

Specifications for the CX-52HD and CX-57HD

57

Flat-Panel LCDs

 

 

 

2

Runco CX-52HD/CX-57HD Owner’s Operating Manual

Image 14
Contents CX-52HD CX-57HD Page ONE Year Limited Warranty RIGHTS, Limits and Exclusions Runco INTERNATIONAL, INC Important Safety Instructions Compliance Information Declaration of ConformityFCC Part Table of Contents Operation Maintenance and TroubleshootingSpecifications Serial CommunicationsList of Figures List of Figures Xii Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Key Features and BenefitsOptional Accessories RuncoCrystal Series LCD at a Glance Controls and IndicatorsControls and Functions Menu Selection ButtonCH / CH Volume Adjustment Buttons VOL / VOL +Power Button Remote Control Sensor Status Indicator LED INPUT4 Component Video RCA connectors Headphone Jack Main Power Switch Power Input 100 to 240 VACINPUT3 Component Video RCA connectors INPUT2 Composite Video InputAIR Antenna Input CX-52HD only Cable Input CX-52HD onlyCrystal Series LCD Remote Control Crystal Series LCD Remote ControlNumeric Buttons Memory Preset ButtonsOFF / on Source Selection ButtonsLetbox Letterbox Aspect Ratio Selection Buttons ANA 169 Anamorphic4X3 Standard Vwide VirtualWideSurrnd Surround Timer OFF ButtonSound Control Buttons Channel Selection Short-Cuts CX-52HD onlyBattery Installation InstallationRemote Control Step Procedure For Details, refer to Quick SetupInstallation Overview Ambient Light Installation ConsiderationsWall-Mounting the Crystal Series LCD Other ConsiderationsSeries LCD to Source Connecting the CrystalConnections to the Crystal Series LCD ComponentsHdmi Connections Rear of the Display Rear of the PC DVD/DTV STB AV OUT Connections Speakers Optional Connecting ExternalConnecting to a Dolby Digital AmplifierConnection Connector Pin AssignmentsRS-232 Controller Rear PanelChanging the OSD Language Turning on the PowerOperation Setting the PC Display Properties Using the On-Screen Menus Setup Picture AdjustTimer SourceAspect Ratio Main MenuSource Input1 Input2 Input3 Input4Aspect Ratio Settings Remote Aspect Ratio Control Description KeyBacklight Color Temp Gamma Save Settings Restore Settings Picture AdjustPicture Adjust Brightness Contrast Color Tint Sharpness Typical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Audio Channel Auto Tuning Add/Erase Favorite Channel Timer CX-52HD only Characteristics of the incoming signal FCC Ratings and Content Categories Rating/Category DescriptionSexual dialogue Operation Menu should be used by ISF-certified technicians only White Balance Gain OffsetCrystal Series LCD Splash Screen Using Picture-In-Picture PIP Available Main and PIP Source Combinations PIP Input SourceChanging the PIP Aspect Ratio Changing the PIP PositionChanging the PIP Size Swapping the Main PIP Images Button on the remote controlPIP Audio Programs Swap button on the remote control Compatibility with Stereo and SAP Audio Broadcasts Broadcast Mode Receive Mode Mono StereoStereo Sound/SAP CX-52HD only Mono+SAPOperation Troubleshooting Tips Maintenance and TroubleshootingCleaning Troubleshooting ChartComputer Signal Serial Commands RS-232 Connection and Port ConfigurationSerial Command Syntax Command DescriptionSAB SDB Key 0105 0054 Serial Communications Crystal Series LCD Specifications SpecificationsCrystal Series LCD Specifications Specifications are subject to change without notice Crystal Series LCD Dimensions CX-52HD DimensionsCX-57HD Dimensions Signal Mode Vertical Horizontal Computer Signal CompatibilityComputer/Video Signal Compatibility Chart Type Frequency Hz Frequency kHzSpecifications Page Runco CL-810 Owner’s Operating Manual