Sanyo VHR-H530 instruction manual Troubleshooting Guide, Symptom Possible Cause Corrective Action

Page 38

SC4HW/NA (VHR-H530 GB) Fri. Jan., 07/2000

TROUBLESHOOTING GUIDE

If you have followed the instructions in this manual and still have difficulty operating your VCR, check the steps below before getting help from a factory-authorized service center.

SYMPTOM

POSSIBLE CAUSE

CORRECTIVE ACTION

 

 

 

No power.

œ The power cord is not connected.

œConnect the power cord to the AC power input socket, then to an AC wall outlet.

 

œ The power is not on.

œ Turn the power on.

The “Auto Setup” message is

œ The VCR is being used for the first

œ The VCR is not set or the settings

displayed when the power is

time or after the power has failed or

have been erased from the memory.

turned on.

has been disconnected for more than

Please refer to INITIAL SETUP to set

 

5 seconds.

the VCR.

 

 

 

Timer recording does not

œ The clock is not set correctly.

œ Set the clock correctly.

function.

œ The program timer is set incorrectly.

œ Set the program timer correctly.

 

 

œ The timer is not set to ON.

œ Turn the power off. TIMER indicator

 

 

will light on the front panel.

Recording is not possible. œ The record safety tab on the cassette is missing.

œThe channel selected on the VCR does not correspond to the cable converter/decoder output channel.

œPlace vinyl tape over the safety tab hole in the cassette.

œSelect the correct channel (CH 02 ~ 07).

The picture is poor during playback.

œThe TV channel selector is not set to the proper channel.

œDuring playback, set the TV’s channel selector to channel 3 or 4 to match the VCR’s channel switch setting.

œThe TV fine tuning is not set correctly.

œFine-tune the TV.

œIf the playback picture is still poor, contact a factory-authorized service center.

White lines (noise bands) in the picture during playback.

œ Poor quality recording or tape.

œ Try a different tape.

No picture during playback.

œ The TV is not set to the proper channel.

œ Set the TV’s channel selector to match

 

 

the VCR’s channel switch setting

 

 

(channel 3 or 4).

 

 

 

Playback picture is partially

œ The tracking control is not set to the

œ Adjust the tracking control for a better

noisy. (horizontal white lines)

proper position.

picture.

TV programs cannot be seen.

œ The cable connections are incorrect.

œ Recheck all cable connections.

37

Image 38
Contents Español EnglishFrançais Location PrecautionsMoisture Condensation Problems Avoiding Electric Shock or FireContents FeaturesAccessories VHS Video Cassette Tapes Auto A/V Selection Locations of Controls and IndicatorsFront Panel Locations of Controls and Indicators Back PanelLocations of Controls Remote ControlUsing the remote control Important Note Remote ControlBattery Installation and Operation Basic ANTENNA/CABLE Connections VCRAlternative Cable TV Connections When the TV does not have a built-in cable converterWhen you have both cable and pay TV scrambled channels Important Notes Cable converter/decoder output channel setupAlternative Cable TV Connections AUDIO/VIDEO Connections When you have a stereo monitor TVWhen you have a monitor TV and a stereo system Stereo ConnectionsIf no XDS signal is available in your area Initial SetupRF output channel setting rule Before startingManual Erase Initial SetupChannel Selection Convenience Manual ProgrammingMultifunction ON-SCREEN Displays Main Menu Options ON-SCREEN MenuDisplaying the On-Screen Menus ON-SCREEN Menu Displaying the VCR Setup Menus Before startingVCR Setup Menu Options Clock set menu appears Setting the ClockAutomatic Clock Adjustment Standard/Daylight Time Adjustment Setting the ClockManual Clock Setting Channel Programming Changing the Menu LanguageProgramming Channels Playback of Copyguarded Tapes Viewing TV onlyPlaying a Rental Tape Automatic Picture Control Normal PlaybackManual Picture Control DPC picture control screen appearsManual Tracking Control Tracking Control AdjustmentsTracking Control Tapes with Hi-Fi SoundRecording One Program While Viewing Another Rec. List Super FeatureRecording Recording Input OptionsRecording Smart Speed Record FunctionRec. List Recording Contents List Super Rec. List SuperEntering the Program Type Type input menu will be displayed on screenStereo/SAP Recording MTS IndicatorsMTS Mode Selection Audio Output Mode Special Playback Index Search Operation Zero SearchIndex Search Index Search e will be displayed on-screenEnd time AM/PM setting will be entered automatically Program Timer RecordingTimer Programming Timer program menu appearsClearing the Program Timer Program Timer RecordingChecking the Program Timer Changing the Program TimerProgram Recording Order Using Timer Recording for Several ProgramsTimer Setting Notes Quick Timer Recording QTR Auto SettingChild Lock Forward picture search begins Sound is mutedCabinet Cleaning MaintenanceHead Care and Cleaning Copying a TapeTroubleshooting Guide Symptom Possible Cause Corrective ActionElectrical Specifications SpecificationsGeneral Specifications Other SpecificationsSC4HW/NA VHR-H530 GB Fri. Jan., 07/2000