Sanyo VHR-H690 Program Timer Recording, Checking the Program Timer, Clearing the Program Timer

Page 37

SC4H/CA3 (VHR-H690 GB) Tue. Mar. 14/2000

PROGRAM TIMER RECORDING

Setting a Program Timer Recording Using the Buttons on the VCR

If the remote control does not operate or is not available you can use the buttons on the VCR front panel to set a program timer recording.

NOTE: Eject the cassette tape, before proceeding with the steps below.

1Press and hold the REC button on the front panel for about 5 seconds.

The Timer program menu appears.

If the clock has not yet been set, the Clock set menu appears.

If necessary, the clock can also be set using the CHANNEL l (or j) and FF buttons. (Refer to the next step for button functions.)

2Use the CHANNEL l (or j) and FF buttons on the VCR front panel to program the timer.

CHANNEL button: To select numbers or switch

settings

FFbutton:To select the next item

NOTE: If you enter the wrong number or setting, press the REW button to return to the wrong number or setting, then enter the correct one.

3When the recording tape speed is set, press the FF button on the front panel to save the settings.

4When finished, press the REC button on the front panel to exit from the menu.

5Load a cassette.

6Press the POWER button.

NOTES:

œDaily or weekly recording, or the program type cannot be set using this method.

œOnce a program timer recording has been set, it cannot be erased using the buttons on the VCR front panel.

Checking the Program Timer

1Turn on the power (TV and VCR).

2Set the TV to channel 3 or 4.

3Press the MENU button. The main MENU appears.

4Press the OK button.

The programmed recordings are listed.

NOTE: To display the program type, press the TYPE button after selecting the desired program using the ù (or û) button.

5When finished, press the MENU button to exit the menu.

6Press the POWER button.

The VCR power turns off and the timer is set to the recording standby mode.

The Timer icon (n) appears.

Clearing the Program Timer

1Follow steps 1 – 4 in “Checking the Program Timer”.

2Press the ù (or û) button to select the program to be cleared.

3Press the CLEAR button.

The erase confirmation screen appears.

4Press the CLEAR button again. (To cancel the erase procedure, press the SET button.)

The selected timer program is erased from the program memory.

5When finished, press the MENU button to exit the menu.

6Press the POWER button.

Changing the Program Timer

1Follow the steps under “Clearing the Program Timer” to erase the program that you wish to change.

2Follow the steps under “Setting a VCR Plus+ Programming System Recording” or “Timer Programming” to add a new timer program.

36

Page 36 Page 38
Image 37
Page 36 Page 38
Contents VHR-H690 Moisture Condensation Problems PrecautionsLocation Avoiding Electric Shock or FireAccessories FeaturescontentsVHS Video Cassette Tapes Front Panel Locations of Controls and IndicatorsAuto A/V Selection Indicator Panel Locations of Controls and IndicatorsOperation Icons Example of IndicationsBack Panel Locations of Controls Multibrand Universal Remote ControlBattery Installation and Operation Multibrand Universal Remote ControlSetting the remote control code Using the remote controlSprucer Catv DSSVCR Basic ANTENNA/CABLE ConnectionsWhen you have both cable and pay TV scrambled channels When the TV does not have a built-in cable converterAlternative Cable TV Connections Alternative Cable TV Connections Cable converter/decoder output channel setupImportant Notes When you have a monitor TV and a stereo system When you have a stereo monitor TVAUDIO/VIDEO Connections Stereo ConnectionsAuto RF output channel setting will start Initial SetupRF output channel setting rule If no XDS signal is available in your areaChannel Selection Convenience Initial SetupManual Erase Manual ProgrammingMultifunction ON-SCREEN Displays Displaying the On-Screen Menus ON-SCREEN MenuMain Menu Options VCR Setup Menu Options Displaying the VCR Setup Menus Before startingON-SCREEN Menu Automatic Clock Adjustment Setting the ClockClock set menu appears Manual Clock Setting Setting the ClockStandard/Daylight Time Adjustment Programming Channels Changing the Menu LanguageChannel Programming Playing a Rental Tape Viewing TV onlyPlayback of Copyguarded Tapes Manual Picture Control Normal PlaybackAutomatic Picture Control DPC picture control screen appearsTracking Control Tracking Control AdjustmentsManual Tracking Control Tapes with Hi-Fi SoundRecording source Indicator shows Rec. List Super FeatureRecording Recording One Program While Viewing AnotherSmart Speed Record Function RecordingRec. List Super Rec. List Recording Contents List SuperType input menu will be displayed on screen Entering the Program TypeMTS Mode Selection MTS IndicatorsStereo/SAP Recording Audio Output Mode Special Playback Index Search Operation Zero SearchIndex Search e will be displayed on-screen VCR Plus+ Timer Setting menu PlusCode number appears Setting a VCR Plus+ Programming System RecordingMinutes are subtracted from or added to the end time VCR Plus+ Programming System Notes VCR Plus+PROGRAMMING SystemTimer Programming Program Timer RecordingTimer program menu appears End time AM/PM setting will be entered automaticallyChecking the Program Timer Program Timer RecordingClearing the Program Timer Changing the Program TimerTimer Setting Notes Using Timer Recording for Several ProgramsProgram Recording Order Auto Setting Quick Timer Recording QTRAppears on the VCR display Forward picture search begins Sound is muted Child LockHead Care and Cleaning MaintenanceCabinet Cleaning AV indicator L1 is displayed instead of a channel numberSymptom Possible Cause Corrective Action Troubleshooting GuideGeneral Specifications SpecificationsElectrical Specifications Other SpecificationsSanyo Canada Inc
Top Page Image Contents