Sanyo VHR-H690 instruction manual Multifunction ON-SCREEN Displays

Page 17

SC4H/CA3 (VHR-H690 GB) Tue. Mar. 14/2000

MULTIFUNCTION ON-SCREEN DISPLAYS

Various displays appear, superimposed over the screen image, indicating the operation mode and features in use.

Operation mode

MTS mode

Status display

1 Press the DISPLAY button on the remote control.

QTR end time

Program title

Channel/AV

The status display appears.

pQTR10:30PM SAP ST C 10

SPORTS DIGEST

SAP ST C 10

 

SP

 

0:00:00

LR

09:30PM

 

 

 

 

 

 

 

 

 

 

Recording

 

 

 

Clock

tape speed

 

Audio output

 

 

 

 

Counter

 

 

 

 

Operation Mode Display

When an operation button is pressed, the corresponding operation mode icon is displayed in the top left corner of the screen for about 3 seconds.

NOTE: The recording pause mode icon will remain displayed until recording is resumed or stopped.

Operation

Icon

Operation

Icon

Play

c

Record

a

Fast-forward

c c

Record pause

a h

Rewind

d d

 

 

Channel Number and MTS Mode Displays

The channel number and the MTS mode displays appear for about 3 seconds when a channel is selected.

Program Title Display

When a channel is tuned or when normal playback is started, the program title (maximum 24 characters) will be displayed for about 4 seconds.

NOTES:

œThe program title is only displayed if the broadcast carries the title information or if it has been recorded on the tape.

œDepending on the TV signal or tape condition the program title may not be displayed even if it is available.

Recording Tape Speed Display

The recording tape speed is displayed for about 3 seconds after recording is started or when the tape speed is changed. The “SS” display means that the smart speed record function is used (see page 26).

SP 0:00:00

LR 09:30PM

2To remove the status display, press the DISPLAY button (press the button twice if a tape is loaded in the VCR).

NOTE: The status display will not appear if a menu is displayed on screen, or during special playback.

Remaining Tape Duration Display

1Press the DISPLAY button twice.

The remaining tape duration appears at the bottom of the screen. It is calculated in hours and minutes from the current position to the end of the tape.

SP Tape remain 2:30

If “ --:--” is displayed, the remaining tape duration has not been calculated.

2To remove the remaining tape duration display, press the DISPLAY button again.

NOTES:

œThe remaining tape duration display will not appear if a menu is displayed on screen or during special playback.

œThis feature will not work properly on T-140 tapes or tapes longer than T-160. (The feature will work on T-160 tapes.)

œDepending on the condition and type of tape used, the VCR may not accurately detect the remaining tape duration.

BASIC OPERATION

16

Page 16 Page 18
Image 17
Page 16 Page 18
Contents VHR-H690 Moisture Condensation Problems PrecautionsLocation Avoiding Electric Shock or FireAccessories FeaturescontentsVHS Video Cassette Tapes Auto A/V Selection Locations of Controls and IndicatorsFront Panel Indicator Panel Locations of Controls and IndicatorsOperation Icons Example of IndicationsBack Panel Locations of Controls Multibrand Universal Remote ControlBattery Installation and Operation Multibrand Universal Remote ControlSetting the remote control code Using the remote controlSprucer Catv DSSVCR Basic ANTENNA/CABLE ConnectionsAlternative Cable TV Connections When the TV does not have a built-in cable converterWhen you have both cable and pay TV scrambled channels Important Notes Cable converter/decoder output channel setupAlternative Cable TV Connections When you have a monitor TV and a stereo system When you have a stereo monitor TVAUDIO/VIDEO Connections Stereo ConnectionsAuto RF output channel setting will start Initial SetupRF output channel setting rule If no XDS signal is available in your areaChannel Selection Convenience Initial SetupManual Erase Manual ProgrammingMultifunction ON-SCREEN Displays Main Menu Options ON-SCREEN MenuDisplaying the On-Screen Menus ON-SCREEN Menu Displaying the VCR Setup Menus Before startingVCR Setup Menu Options Clock set menu appears Setting the ClockAutomatic Clock Adjustment Standard/Daylight Time Adjustment Setting the ClockManual Clock Setting Channel Programming Changing the Menu LanguageProgramming Channels Playback of Copyguarded Tapes Viewing TV onlyPlaying a Rental Tape Manual Picture Control Normal PlaybackAutomatic Picture Control DPC picture control screen appearsTracking Control Tracking Control AdjustmentsManual Tracking Control Tapes with Hi-Fi SoundRecording source Indicator shows Rec. List Super FeatureRecording Recording One Program While Viewing AnotherSmart Speed Record Function RecordingRec. List Super Rec. List Recording Contents List SuperType input menu will be displayed on screen Entering the Program TypeStereo/SAP Recording MTS IndicatorsMTS Mode Selection Audio Output Mode Special Playback Index Search e will be displayed on-screen Zero SearchIndex Search Operation Minutes are subtracted from or added to the end time Setting a VCR Plus+ Programming System RecordingVCR Plus+ Timer Setting menu PlusCode number appears VCR Plus+ Programming System Notes VCR Plus+PROGRAMMING SystemTimer Programming Program Timer RecordingTimer program menu appears End time AM/PM setting will be entered automaticallyChecking the Program Timer Program Timer RecordingClearing the Program Timer Changing the Program TimerProgram Recording Order Using Timer Recording for Several ProgramsTimer Setting Notes Appears on the VCR display Quick Timer Recording QTRAuto Setting Forward picture search begins Sound is muted Child LockHead Care and Cleaning MaintenanceCabinet Cleaning AV indicator L1 is displayed instead of a channel numberSymptom Possible Cause Corrective Action Troubleshooting GuideGeneral Specifications SpecificationsElectrical Specifications Other SpecificationsSanyo Canada Inc
Top Page Image Contents