Sanyo DP19241 owner manual Connections to other equipment

Page 15

Connections to other equipment

Using an AV Amplifier with built-in digital surround

If you are using an Amplifier with built-in digital surround sound, you can enjoy various audio systems including Dolby Digital Surround audio that sounds just like the movie.

Connect an AV amplifier with built-in Dolby Digital decoder, etc. as shown below.

Rear of the unit

To DIGITAL AUDIO

COAXIAL OUT

Coaxial digital cable (not supplied)

Front

Speaker

(Left)

Front

Subwoofer Speaker

(Right)

TV

To Coaxial

Digital Audio IN

AV Amplifier with built-in digital surround decoder as listed above

 

Center Speaker

Surround

Surround

Speaker (Left)

Speaker

 

(Right)

NOTE:

• When you are viewing digital broadcast, this unit will not work in conjunction with DTS audio or MPEG audio. There will be no sound output if connected to an AV amplifier with a built-in DTS decoder or MPEG decoder.

• Digital Audio Output terminal does not output the sounds from devices connected by HDMI.

To connect a HDMI or a DVI device to the unit

The HDMI input receives digital audio and uncompressed video from a HDMI device or uncompressed digital video from a DVI device.

When you connect to a DVI device with a HDMI-to-DVI adapter cable, it transfers only video signal. Separate analog audio cords required.

Left of the unit

 

To HDMI/DVI IN

 

HDMI cable (type A connector)

To PC/DVI

(not supplied)

HDMI - to - DVI adapter cable

AUDIO IN

 

(HDMI type A connector)

 

(not supplied)

 

Audio cord (not supplied)

To HDMI out HDMI device

or

DVI device

To DVI output

ENGLISH

NOTE:

• When using HDMI/DVI to connect your HDMI or DVI devices, you must select the corresponding audio input source (HDMI or DVI) on the menu screen (see page 19). Otherwise you will only see the image with no sound.

• If you connect an external component (cable box, satellite receiver, etc.) to this LCD TV using an HDMI cable or a DVI to HDMI cable, the image will not display if the output resolution of the component is set to 480i. To receive the picture you must change the output resolution on the external component.

Should you require further instruction, please contact the manufacturer of the external component.

15

3FR0321A_En.indd 15

1/7/11 4:32:11 PM

Page 14 Page 16
Image 15
Page 14 Page 16
Contents DP19241 Warranty Application HOW to Make a Claim Under this WarrantyObligations Trademarks Location of the required Marking To provide some protection against This Manufacturer Cares Child SafetyIssue Tune Into SafetyCondensation HOW to Handle the LCD PanelHow to remove the stand How to attach the standFeatures Power sourceTo USE AC Power Contents Right side Parts and functionsFront RearBattery Precautions Remote controlCombination VHF/UHF Antenna Single 75 ohm cable Antenna connectionsLeft of the unit Connections to other equipmentTo connect the LCD TV to a VCR To connect the LCD TV to a camcorder, or a TV GameConnections to other equipment Using an AV Amplifier with built-in digital surroundVertical To connect the TV to a PC Personal ComputerRGB Aspect RatioTo Select Digital Channels To select the video input sourceTo Select Analog Channels EnterDisplay Quick guide for menu operationConvenience functions Icon Selected Items Setup hintAdding Channel Memorizing channelsAir/Cable selection Automatic SearchTo create channel labels Checking the digital signal strengthLabeling channels Clear AllTo set the V-Chip Setting the V-ChipTo register a password To change the passwordTo clear the all V-Chip settings Closed CaptionCC advanced Setting the picture size Ignition Reception disturbancesSymptoms Possible Solutions TroubleshootingSpecifications AccessoriesGeneral
Top Page Image Contents