B&B Electronics 1939STB manual Arbitration Field

Page 39

Arbitration Field

S

Priority

 

R

D

PDU Format (PF)

 

 

S

I

PF

 

 

 

PDU Specific

 

 

 

Source Address

R

O

3 Bits

 

1

P

 

8 Bits

 

 

 

 

R

D

Cont.

 

 

8 Bits

 

 

 

 

 

 

8 Bits

T

F

 

 

 

*

 

 

 

 

 

 

 

 

S

E

 

 

 

 

 

 

 

 

 

 

 

(See note below.)

R

X

1

1

0

0

0

1

 

1

1

1

0

0

X

X

0

0

0

0

0

0

0

1

1

0

 

 

 

 

 

 

 

 

X

X

1

2

4

5

6

7

 

8

9

10

11

12

X

X

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

X

X

 

 

Byte 7

 

 

 

 

 

Byte 8

 

X

X

Byte E 8 cont.

 

 

 

 

Byte 9

 

 

 

 

Byte 10

X

X

7

6

5

4

3

2

 

1

0

7

6

5

X

X

4

3

2

1

0

7

6

5

4

3

2

1

0

7

6

5

4

3

X

X

 

 

 

 

 

 

 

 

 

 

 

 

X

X

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

X

X

 

 

 

 

 

 

 

 

 

 

 

 

X

X

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

X

* R1 is the reserved bit. ALL messages should set the SAE reserved bit to 0 on transmit.

The frame above represents the J1939 frame and shows how the data is coded, to be entered into the frame.

The bits marked with an X are set by the controller and are NOT settable by the user and can be ignored.

The easiest way to fill this out is to start at SOF bit, fill in the priority bits (3), the R1 bit, the data page DP bit and so on.

After all 30 bits are set, break apart the bits in bytes following the separation highlighted in gray.

The bytes are converted to hex and can be entered into the communication program provided by B&B as follows:

NOTE: The bytes in the rest of the message (bytes 3, 4, 5, 6, and 11) must be filled out for the message to operate properly.

A-2

1939STB4600 Manual

Appendix A

 

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100

- Fax 815-433-5104

 

B&B Electronics Ltd – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91 792444

– Fax +353 91 792445

Image 39
Contents Model 1939STB RS-232 to J1939 Converter CETable of Contents SAE Publications Introduction1939STB4600 Manual Description Physical Description Electrical SpecificationCommunication directed to the device Format Byte 3 Nibble Control ByteByte Message Received from the SAE-J1939 Bus Vendor String SetupInternal Functions Vendor StringRS-232 Baud Change Baud Rate SetupRS-232 Baud Rate Change cont’d Byte 5 UB3 Parity SetupWord Length Stop Bit SetupJ1939 Format External CommandsValid Codes for Byte Message Header SetupTwo Bit Values for Byte 5 Message Information J1939 Message InformationIntpnd ByteTransmit DLC DIR XTD Bit2J1939 Message Frame SAE-J1939 Control Header1939STB4600 Manual Shown in Table Byte1939STB4600 Manual Byte 1939STB4600 Manual Bytes 9 1939STB4600 Manual DIR Message Direction DLC Data Length CodeData Field Reception of Data SAE-J1939 BusID Byte Function Internal Messages Software Installation1939STB4600 Manual Message Transmission sending data to the 1939STB File Logging Saving Message InformationAppendix A. The Extended can / SAE-J1939 Message Frame Arbitration Field Appendix B. Example