Runco VX-8D operation manual Installation, Remote Control

Page 31

3. Installation

Note

Installation must be performed by a qualified custom video

installation specialist.

To install batteries in the remote control, press up on the battery cover retainer clip and lift off the cover. Install the two AAA batteries with the correct polarity and then replace the cover.

Make sure that the battery polarities are correct when installing the batteries.

Do not mix an old battery with a new one or different types of batteries.

If you will not use the remote control for a long time, remove the batteries to avoid damage from battery leakage.

Make sure that there is nothing obstructing the infrared beam between the remote control and the IR receiver on the projector.

If the effective range of the remote control decreases, or it stops working, replace the batteries with new ones.

The remote control may fail to operate if the infrared remote sensor is exposed to bright sunlight or fluorescent lighting.

Ambient conditions may possibly impede the operation of the remote control. If this happens, point the remote control at the projector, and repeat the operation.

3.1

Remote Control

Notes on Batteries

Notes on Remote Control Operation

Runco VX-8d Installation/Operation Manual

15

Image 31
Contents VX-8d Page RuncoCare Standard Features RuncoCare Standard Two Year Limited WarrantyRuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Declaration of Conformity Compliance InformationFCC Part Page Table of Contents Operation Maintenance and Troubleshooting Table of Contents Xiv List of Figures Xvi About This Manual IntroductionIf you need Turn to Using This ManualFormat screen Description, Features and BenefitsOptional Accessories VX-8d at a Glance Controls and FunctionsExhaust Vent VX-8d Rear Panel Power Input 100 to 240 VAC Connect the VX-8d to power hereRS-232C Input 9-pin, female D-Sub DHD Controller Front Panel DHD Controller Front PanelPanel DHD Controller RearDisplay Control Inputs 4. USB DHD Controller/VX-8d Remote Control VX-8d Remote Control UnitCursor Buttons On / OFFComp Component Letbox Letterbox Memory Preset ButtonsAspect Ratio Selection Buttons 169Controls and Functions Remote Control InstallationInstallation Overview Quick SetupStep Procedure For Details, Refer to Projector Installation Options Installation ConsiderationsInstallation Type Throw Distance Ambient LightLens VX-8d Lens Options and Throw RatiosThrow Range Throw Ratio Inches, with Lens OptionPosition Ceiling InstallationFloor Installation Vertical and HorizontalHorizontal Lens Shift Example only Input Timing Possible Audio Latency milliseconds Synchronization IssuesPossible Audio Latency for Various Input Timings Audio/VideoOther Considerations Installing the Optional CineWide Lens MountLens Motor VX-8d/CineWide with AutoScope Installing the AutoScopeInstalling the Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation Installing the Fixed CineWide Base Plate VX-8d/CineWide Ceiling Mounting Adjusting the ProjectionDo not use the mounting screws provided with the ceiling Floor Mounting UprightController to the VX-8d Connector Panel AccessConnecting the DHD Connections to the VX-8d and DHD Controller11. RS-232 Connection from the DHD Controller to the VX-8d Controller Connecting SourceComponents to the DHD Hdmi Source Connections See FigureDTV-Set-Top Box 13. Component Video Source Connections14. Rgbhv Source Connections Computer RGB Camcorder15. Scart Rgbs Source Connections Gaming ConsoleCamcorder Composite and S-Video Source ConnectionsConnection RS-232 ControllerAutoScope Lens Motor Rear Connecting 12-volt Trigger Outputs to External EquipmentReceiver to the DHD Connecting an External IRConnecting to AC Power Turning on the PowerAdjusting the Picture Orientation Primary Lens AdjustmentsFocus Zoom Vertical and Horizontal Lens Shift Anamorphic Lens Installation Adjustment Installing and Adjusting the CineWide Anamorphic LensIt is extremely important that the primary lens is properly 21. Attaching the Anamorphic Lens to the Lens Ring Adjusting the Horizontal X Lens Position Installation Anamorphic Lens Top View Geometry Operation Using the On-Screen MenusMain Menu ServiceRunco Video Aspect Ratio Input SourceAspect Ratio Input SourceHdtv programs in their Aspect Ratio SettingsRemote Aspect Ratio Control Description Key 169 Select 169 to view 169 DVDsOverscan Remote Aspect Ratio Control Description KeyPicture PictureTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Input Position Input PositionOverscan Modes Memory Presets Memory PresetsCalibration InformationCIE 1931 Chromaticity Diagram Color Temperature Preset Associated x/y Values Color Temperature Presets and Associated Color PointsCopy/Paste Copied settings are not retained after a power cycleService ServiceInput Names Exit Operation Color X/y Color Gamut ValuesLCD 58 and ISF Day/Night Memory Presets Lamp Replacement Maintenance and TroubleshootingTroubleshooting Chart Troubleshooting TipsSymptom Possible Causes Solution Serial Command Syntax RS-232 Connection and Port ConfigurationSerial Communications Input Selection Commands Serial CommandsPicture Adjust Commands Output Shift Commands Input Position CommandsExit Return key Enter keySerial Communications VX-8d Specifications SpecificationsVX-8d Specifications Limited Warranty Home Theater Calibration SpecificationsIndustry-Standard Specifications Weight without lensDHD Controller Specifications DHD Controller SpecificationsVX-8d Dimensions with Optional Ceiling Mount VX-8d DimensionsVX-8d/CineWide Dimensions with Optional Ceiling Mount VX-8d/CineWide DimensionsVX-8d/CineWide with AutoScope Dimensions VX-8d/CineWide with AutoScope DimensionsSupported? √ = Yes, = No Supported Signal Timings by InputFormat Resolution Frequency Rate Hz MHz KHz Supported TimingsPAL-B/G/H/I PAL-M Specifications Page 020-0965-01 Rev. a February
Related manuals
Manual 108 pages 57.39 Kb