Runco VX-8D operation manual Installing the AutoScope, Lens Motor VX-8d/CineWide with AutoScope

Page 40

Installation

Installing the AutoScope ➤	Figure 3-6shows the VX-8d/CineWide with AutoScope motor assembly.
Lens Motor
(VX-8d/CineWide with
AutoScope)	Screw, Phillips Pan-Head, 2
	10-32 x 3/8” (12x)	CineWide with AutoScope
	3	Ceiling Mount Adapter/
		Projector Stand, Right
	AutoScope 1
	Lens Motor

4 CineWide with AutoScope Ceiling Mount Adapter/ Projector Stand, Left

Figure 3-6. VX-8d/CineWide with AutoScope Motor Assembly – Exploded View

Remove Projector Front Feet: Place the projector upside down on a blanket or other soft surface. Loosen and remove the two front feet on the projector.

Install Ceiling Mount Adapters/Projector Stands: For ceiling installations, the adapters bring the attachment points for the projector mounting rails (included with the projector ceiling mount kit) from the bottom of the projector up and around the AutoScope lens motor housing. For floor installations (where the projector is upright), the adapters allow the projector to lie flat on the mounting surface.

Using eight (8) each of the supplied, Pan-Head Phillips screws, attach the AutoScope

Ceiling Mount Adapters/Projector Stands to the projector as shown in Figure 3-7.

24	Runco VX-8d Installation/Operation Manual

Image 40

Contents VX-8d Page RuncoCare Standard Two Year Limited Warranty RuncoCare Standard FeaturesRuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Compliance Information Declaration of ConformityFCC Part Page Table of Contents Operation Maintenance and Troubleshooting Table of Contents Xiv List of Figures Xvi Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Format screenOptional Accessories Controls and Functions VX-8d at a GlanceExhaust Vent VX-8d Rear Panel Power Input 100 to 240 VAC Connect the VX-8d to power hereRS-232C Input 9-pin, female D-Sub DHD Controller Front Panel DHD Controller Front PanelPanel DHD Controller RearDisplay Control Inputs 4. USB VX-8d Remote Control Unit DHD Controller/VX-8d Remote ControlCursor Buttons On / OFFComp Component Memory Preset Buttons Aspect Ratio Selection Buttons169 Letbox LetterboxControls and Functions Installation Remote ControlInstallation Overview Quick SetupStep Procedure For Details, Refer to Projector Installation Options Installation ConsiderationsInstallation Type Ambient Light Throw DistanceVX-8d Lens Options and Throw Ratios Throw Range Throw Ratio Inches, withLens Option LensCeiling Installation Floor InstallationVertical and Horizontal PositionHorizontal Lens Shift Example only Synchronization Issues Possible Audio Latency for Various Input TimingsAudio/Video Input Timing Possible Audio Latency millisecondsInstalling the Optional CineWide Lens Mount Other ConsiderationsInstalling the AutoScope Lens Motor VX-8d/CineWide with AutoScopeInstalling the Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation Installing the Fixed CineWide Base Plate VX-8d/CineWide Adjusting the Projection Do not use the mounting screws provided with the ceilingFloor Mounting Upright Ceiling MountingConnector Panel Access Connecting the DHDConnections to the VX-8d and DHD Controller Controller to the VX-8d11. RS-232 Connection from the DHD Controller to the VX-8d Connecting Source Components to the DHDHdmi Source Connections See Figure Controller13. Component Video Source Connections DTV-Set-Top BoxComputer RGB Camcorder 14. Rgbhv Source ConnectionsGaming Console 15. Scart Rgbs Source ConnectionsComposite and S-Video Source Connections CamcorderRS-232 Controller ConnectionConnecting 12-volt Trigger Outputs to External Equipment AutoScope Lens Motor RearConnecting an External IR Receiver to the DHDTurning on the Power Connecting to AC PowerAdjusting the Picture Orientation Primary Lens AdjustmentsFocus Zoom Vertical and Horizontal Lens Shift Anamorphic Lens Installation Adjustment Installing and Adjusting the CineWide Anamorphic LensIt is extremely important that the primary lens is properly 21. Attaching the Anamorphic Lens to the Lens Ring Adjusting the Horizontal X Lens Position Installation Anamorphic Lens Top View Geometry Using the On-Screen Menus OperationMain Menu ServiceRunco Video Input Source Aspect RatioInput Source Aspect RatioAspect Ratio Settings Remote Aspect Ratio Control Description Key 169Select 169 to view 169 DVDs Hdtv programs in theirRemote Aspect Ratio Control Description Key OverscanPicture PictureTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Input Position Input PositionOverscan Modes Memory Presets Memory PresetsInformation CalibrationCIE 1931 Chromaticity Diagram Color Temperature Presets and Associated Color Points Color Temperature Preset Associated x/y ValuesCopied settings are not retained after a power cycle Copy/PasteService ServiceInput Names Exit Operation X/y Color Gamut Values ColorLCD 58 and ISF Day/Night Memory Presets Maintenance and Troubleshooting Lamp ReplacementTroubleshooting Chart Troubleshooting TipsSymptom Possible Causes Solution Serial Command Syntax RS-232 Connection and Port ConfigurationSerial Communications Serial Commands Input Selection CommandsPicture Adjust Commands Input Position Commands Output Shift CommandsEnter key Exit Return keySerial Communications VX-8d Specifications SpecificationsVX-8d Specifications Home Theater Calibration Specifications Industry-Standard SpecificationsWeight without lens Limited WarrantyDHD Controller Specifications DHD Controller SpecificationsVX-8d Dimensions VX-8d Dimensions with Optional Ceiling MountVX-8d/CineWide Dimensions VX-8d/CineWide Dimensions with Optional Ceiling MountVX-8d/CineWide with AutoScope Dimensions VX-8d/CineWide with AutoScope DimensionsSupported Signal Timings by Input Format Resolution Frequency Rate Hz MHz KHzSupported Timings Supported? √ = Yes, = NoPAL-B/G/H/I PAL-M Specifications Page 020-0965-01 Rev. a February

Related manuals

Manual 108 pages 57.39 Kb