Zenith XBV323 warranty Tape Operation Normal Playback, Special Effect Playbacks

Page 21

Tape Operation

Normal Playback

Preparation:

Turn on the TV.

Tune the TV to the DVD+VCR output channel (CH 3 or 4) or set the TV’s source selector to VIDEO.

If a direct VIDEO/AUDIO connection is made between the DVD+VCR and the TV, set the TV’s source selector to VIDEO. Set the Output Source to VCR as shown in “Selecting the Output Source” on page 6.

1

Insert a prerecorded video cassette.

The

indicator will light and the DVD+VCR will

power-up automatically.

Make sure that the indicator in the display window is not lighted. If it is, press POWER once. If a tape without a safety tab is inserted, the unit will start playback automatically.

2 Press PLAY (H) once.

PLAY appears on the TV screen .

It is not necessary to select the tape speed for playback. It will be automatically selected by the DVD+VCR.

In playback, the TV/VCR selector switches to VCR mode automatically.

3 Press STOP (x) to stop playback. STOP appears on the TV screen.

If the tape reaches the end before STOP (x) is pressed, the DVD+VCR will automatically stop, rewind and eject the tape, and it will turn itself off.

Tracking Control

Auto Tracking

The automatic tracking function adjusts the picture to remove snow or streaks.

The AUTO TRACKING function works in the following cases:

A tape is played back for the first time. Tape speed (SP, LP, SLP) changes.

Streaks or snow appear because of scratches on the tape.

Manual Tracking

If noise appears on the screen during playback, press either v/V on the remote control or CH (v/V) on the front panel until the noise on the screen is reduced.

In case of vertical jitter, adjust these controls very carefully. Tracking is automatically reset to normal when the tape is ejected or the power cord is unplugged for more than 3 seconds.

Special Effect Playbacks

Special effects playback notes

Horizontal lines (noise bars) will appear on the TV screen. This is normal.

The audio is automatically muted during special effect modes, so there is no sound during search.

During high-speed picture search mode, a short period is needed to stabilize tape speed when re-entering the PLAY mode. Slight interference may be observed during this period.

Search

This function lets you quickly and visually search for a desired tape section in either direction: forward or reverse.

1

Press BACKWARD (.) or FORWARD (>)

OPERATION

 

during playback.

 

 

 

The DVD+VCR will be activated in the SEARCH

 

 

mode.

 

 

If the DVD+VCR is left in the SEARCH mode for more

 

 

than 3 minutes, the DVD+VCR will automatically enter the

 

2

PLAY mode, to protect the tape and video heads.

 

To return to playback, press PLAY (H).

 

Still Picture and Frame-by-Frame Playback

1Press PAUSE/STEP (X) during playback. Still picture will appear on the TV screen.

If a still picture vibrates vertically, stabilize it using v/V on the remote control.

If the DVD+VCR is left in the STILL mode for more than 5 minutes, the DVD+VCR will automatically enter the STOP mode to protect the tape and video heads.

2Press PAUSE/STEP (X) repeatedly to advance the video picture one frame at a time while viewing a still picture.

3To return to playback, press PLAY (H).

Slow Motion

1While in still mode, press FORWARD (>).

The tape will be played back at a speed 1/19 times slower than the normal speed.

During slow playback, use v/V on the Remote Control to minimize noise bands.

If slow motion mode continues for more than 3 minutes, the DVD+VCR will automatically change to playback mode.

2To return to playback, press PLAY (H).

CM Skip (Commercial Skip)

This is useful for skipping commercials or short program segments.

1Press CM Skip during playback.

The tape will fast forward picture search through 30 seconds of recording.

Skipping time can be extended by pressing CM Skip repeatedly.

Subsequent presses result in advancing the fast forward picture search time by 30-second increments (maximum 3 minutes).

2When the search is complete, the DVD+VCR will go into playback mode automatically.

EZ (EASY) Review

You can replay a specified segment twice.

1

During playback, press and hold EZ REVIEW for

more than 3 seconds at the end of the segment

 

and your VCR will start reverse search.

2 Release EZ REVIEW at the beginning of the segment. The segment is replayed twice automatically.

To return to normal play, press PLAY (H) during easy review playback.

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Installation and Operating Guide Warranty Regulatory Information FCC Part Safety PrecautionsImportant Safety Instructions Table of Contents Remote Control Operating Range Remote Control Battery InstallationBefore Use Playable DiscsPrecautions About SymbolsSelecting the Viewing Source Front Panel Controls REC Display WindowRemote Control Video OUT DVD OUT Connections PanelComponent Video OUT RF. OUTDVD/VCR OUTConnections Connecting Antenna/Cable TV toOptional, Preferred TV Connections Connections Basic TV ConnectionsAccessory Audio/Video A/V Connections to Connections Optional, Preferred TV ConnectionsDigital Multi-channel sound On-Screen Menus Setup Before VCR Operation On-Screen Display OSDMenu Selection Function OSD Audio ModeLanguage Select Broadcast Type STEREO/SAP/MONOBefore VCR Operation Setting the Clock Auto Clock SetManual Clock Set Before DVD Operation General Explanation On-Screen DisplayOn-screen display operation General Operation Before DVD Operation DVD SetupLanguage PictureBefore DVD Operation SoundOthers Country Code DVD Rating DVD Parental ControlSpecial Effect Playbacks Tape Operation Normal PlaybackTape Operation Normal Recording Timer RecordingTo pause recording To record one TV program while watching anotherChecking Erasing Timer Record Programming Tape OperationProgram Priority Checking the Recording Time Instant Timer RecordingTo extend the Recording Time Dubbing and EditingVHS Hi-Fi Stereo System MTS Broadcast Multichannel TV Sound Indicator MTSPlayback with Hi-Fi Stereo Audio Sound MTS Multi-Channel TV SoundAdditional Information Tape Operation Tape Counter Memory FeatureDVD Operation Playing DVDs General FeaturesDVD Operation General Features Special DVD Features About WMA Window Media Audio Files About MP3Audio CD and MP3/WMA Disc Operation Selecting other Files Jpeg Files Operation Viewing Jpeg files JpegStill Picture To flip the pictureProgrammed Playback with Audio CDs and MP3/WMA Discs Programmed Playback CD MP3 WMASymptom Cause Correction TroubleshootingSymptom Cause Correction DVD+VCR is in Timer modeMoisture Condensation Language Code Language Code ListCode Country Country Code ListVCR Specifications SpecificationsDVD Specifications GeneralPage Customer INTER-ACTIVE Center Numbers

XBV323 specifications

The Zenith XBV323 is a multifaceted entertainment device that integrates both a DVD player and a VCR, making it a convenient choice for those looking to bridge the gap between analog and digital media formats. This versatile unit supports a variety of playback formats, which includes DVDs, CDs, and VHS tapes, allowing users to enjoy their favorite movies, music, and shows from different eras all in one place.

One of the main features of the Zenith XBV323 is its comprehensive compatibility with various media formats. The device can play DVD-R/RW, CD-R/RW, and VCD formats, ensuring that users have flexibility in their media library. Additionally, the built-in VCR allows playback and recording of VHS tapes, a significant advantage for users who still have cherished tapes in their collection. This dual functionality promotes ease of use, reducing the need for multiple devices cluttering up entertainment spaces.

The Zenith XBV323 also incorporates several advanced technologies to enhance the viewing experience. It supports various audio and video output options, including standard composite video and stereo audio outputs, making connectivity to existing television systems straightforward. The unit is equipped with features such as progressive scan for DVDs, which significantly improves video clarity, providing a crisper, more detailed picture.

For an improved user experience, the Zenith XBV323 features an intuitive on-screen display. This user-friendly interface simplifies navigation through menus and settings, making it accessible for users of all ages. Furthermore, it is designed with a programmable timer that allows for scheduling of VCR recordings, ensuring that users never miss their favorite shows or movies.

In terms of design, the Zenith XBV323 is compact and stylish, making it a suitable addition to any home theater setup. Its straightforward controls and buttons make operating the device easy, while the remote control enhances convenience, allowing users to manage their entertainment from a distance.

In conclusion, the Zenith XBV323 stands out for its versatility and user-friendly features. By combining the functions of a DVD player and VCR, and supporting a range of media formats, it caters to diverse entertainment needs, making it an asset for anyone looking to enjoy both modern and classic media formats effortlessly. Whether revisiting nostalgic VHS tapes or diving into the latest DVD releases, the Zenith XBV323 ensures a seamless viewing experience.
Top Page Image Contents