Cable Specifications

Fiber Cable

MULTIMODE

Fiber Optic Cable Recommended:	62.5 / 125 µm multimode fiber
Optional:	100 / 140 µm multimode fiber
	85 / 125 µm multimode fiber
	50 / 125 µm multimode fiber
SGETF1013	850 nM
Fiber Optic Transmitter Power:	min: -10.0 dBm	max: -4.0 dBm
Fiber Optic Receiver Sensitivity:	min: -17.0 dBm	max: -0.0 dBm
Link Budget:	7.0 dB
Typical Maximum Cable Distance*:	220 meters
SGETF1018	850 nM
Fiber Optic Transmitter Power:	min: -9.5 dBm	max: -4.0 dBm
Fiber Optic Receiver Sensitivity:	min: -17.0 dBm	max: -0.0 dBm
Link Budget:	7.0 dB
Typical Maximum Cable Distance*:	220 meters

SINGLEMODE

Fiber Optic Cable Recommended:	9 µm singlemode fiber
SGETF1014	1300 nM
Fiber-optic Transmitter Power:	min: -13.0 dBm	max: -3.0 dBm
Fiber-optic Receiver Sensitivity:	min: -20.0 dBm	max: -3.0 dBm
Link Budget:	7.0 dB
Typical Maximum Cable Distance*:	5 kilometers
SGETF1015	1300 nM
Fiber-optic Transmitter Power:	min: -5.0 dBm	max: -0.0 dBm
Fiber-optic Receiver Sensitivity:	min: -20.0 dBm	max: -3.0 dBm
Link Budget:	15.0 dB
Typical Maximum Cable Distance*:	25 kilometers
SGETF1017	1550 nM
Fiber-optic Transmitter Power:	min: -3.0 dBm	max: -2.0 dBm
Fiber-optic Receiver Sensitivity:	min: -23.0 dBm	max: -3.0 dBm
Link Budget:	20.0 dB
Typical Maximum Cable Distance*:	65 kilometers
SGETF1025	1550 nM
Fiber-optic Transmitter Power:	min: -9.5 dBm	max: -3.0 dBm
Fiber-optic Receiver Sensitivity:	min: -20.0 dBm	max: -3.0 dBm
Link Budget:	20.0 dB
Typical Maximum Cable Distance*:	65 kilometers

*Actual distance dependent upon physical characteristics of network installation.

Copper Cable

Category 5 twisted-pair copper wire is required. Either shielded twisted-pair (STP) or unshielded twisted-pair (UTP) can be used. DO NOT USE FLAT OR SILVER SATIN WIRE.

CATEGORY 5:

Gauge	24 to 22 AWG
Attenuation	22.0 dB /100m @ 100 MHz
Maximum Cable Distance:	100 meters

The Gigabit Ethernet™ network uses all four wire pairs. The active pairs are pins 1 & 2, pins 3 & 6, pins 4 & 5, and pins 7 & 8. Use only dedicated wire pairs (such as blue/white

&white/blue, orange/white & white/orange) for the active pins. NOTE: Straight- through/crossover configuration is automatic.

Install Cable

COPPER

NOTE: The SGETF10xx series media converter auto-negotiationfeature allows the media converter to bring up the copper link in the highest mode possible for ALL the attached network devices.

1.Locate or build 1000BASE-TX-compliant cables with male RJ-45 connectors installed at both ends.

2.Connect RJ-45 connector at one end of cable to media converter RJ-45 port connector.

3.Connect RJ-45 connector at other end of cable to 1000BASE-TX- compliant device RJ-45 port connector.

FIBER

1.Locate or build 1000BASE-SX/LX-compliant fiber cable with male two-stranded TX to RX connectors installed at both ends.

TX	TX
RX	RX

2.Connect cable with connector installed at TX location on media converter to RX location on attached device.

3.Connect cable with connector installed at RX location on media converter to TX location on attached device.

Power the Media Converter

1.Install power adapter cord at back of media converter.

2.Connect power adapter plug to AC power.

3.Verify that media converter is powered by observing illuminated LED(s).