Speco Technologies PC Pro Series FCC Notice Class a, Federal Communications Commission Statement

Page 3

FCC NOTICE (Class A)

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may

cause undesired operation.

Federal Communications Commission Statement

NOTE- This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by tuning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/television technician for help.

European Community Compliance Statement (Class A)

This product is herewith confirmed to comply with the requirements set out in the Council Directives on the Approximation of the laws of the Member States relating to

Electromagnetic Compatibility Directive 2004/108/EEC.

Warning - This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures to correct this interference.

DISCLAIMER

No warranty or representation, either expressed or implied, is made with respect to the contents of this documentation, its quality, performance, merchantability, or fitness for a particular purpose. Information presented in this documentation has been carefully checked for reliability; however, no responsibility is assumed for inaccuracies. The information contained in this documentation is subject to change without notice.

In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use this product or documentation, even if advised of the possibility of such damages.

TRADEMARKS

All other products or corporate names mentioned in this documentation are for identification and explanation purposes only, and may be trademarks or registered trademarks of their respective owners.

COPYRIGHT

All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form by any means without the written permission of the manufacturer.

Image 3
Contents PC Pro Series 300AC2FA-CPM M a D E I N T a I W a N FCC Notice Class a Federal Communications Commission StatementEuropean Community Compliance Statement Class a Battery Safety Information Manual Conventions Table of Contents Chapter Using Functional Keys Using the Remote Programs Appendix a Chapter Introduction Package ContentsPC Pro Series SpecificationSoftware Features Dispatch Server Remote AccessCentral ManagementName Function Front PanelNameFunction To Chapter Speed shuttle for adjusting reversed Mode Function Front Panel Control Buttons in Guest ModeChannels Back PanelChannels Connecting Device Hardware InstallationRemote Controller Buttons Name Function Name Function Functional key for multiple system control Name Function Remote Controller Buttons in Guest Mode Pin # Definition Sensor/Relay Interface pinhole allocation8Cahnnels Channels Audio In Interface pinhole allocationUsing the DVR Software Function buttons in Advanced/Preview ModeRunning the Unit for the First Time To allow recording. The button turns violet when it is Setup Using Event Log Viewer Using the POS Viewer Using the Object Viewer Function Buttons in Playback Mode To start playing the recorded video file Full screen Function Buttons in Compact Mode Function Buttons in PTZ Camera Controller To Set Up the Emap Setting Up and Using the EmapTo Use the Emap To Cut and Save the Wanted Portion of the Recorded VideoTo Bookmark a Section of the Video To Search Using the Visual SearchTo Search Using the Event Search To Search Using the Intelligent Search Setup the PTZ Camera To Setup the PTZ/IP PTZ CameraSetup the IP PTZ Camera System Setting Customizing the DVR SystemStorage Path Hard Disk Calculator Advance button 3LanguageVideo Standard Call Monitor OutConfiguration System Controller SetupBaud rate 9600 Data bits Parity Stop bit Flow control System Configuration Date/Time SetupIP Setup Display HDD FormatAutomatically Select Automaitc ManualLogin Beep if no signalPlayback Mode Enable OverlayTo Set the POS Setting Page Camera Setting Face Finder Object CountingAnalog Camera Enable Mark to enable Trigger Condition SettingVideo Screen InputIP Camera Remote DVRClick Detail to enter the object counting setup window Setup the Object CountingRecording Setting Voice Detection Enable AudioNo Recording Motion DetectionTo Mask/Shield an area on the screen To show and change the color of the MaskTo Playback Encrypted Video Network Setting User Information Remote Control ServerNetwork Video Configuration WebViewer ConfigurationNetwork Bandwidth Limit Other Configuration UPnPEnable White List Enable HandyViewSchedule Setting Turn on Relay # Backup SettingTo Backup file Set schedule at specific portion of timeClick Quick Backup Setup Quick BackupSensor Setting To Setup External I/O Box Page Relay Setting To set the Alarm Setting Alarm SettingLaunch Emap Make Phone Calls Enlarge Camera ViewRelay Output Play Warning SoundStart Recording SMS Short Message Service/MMS Multimedia Messaging SystemPTZ preset point Alarm SOP Standard Operation ProcedureTo Setup the Alarm Sound Setting To Setup Alarm RelayTo Setup Call Out List To Setup Send E-mail SettingMail Server Mail To Setup FTP SettingTo Setup Alarm Recording Setting Modem Dial up SettingTo Setup SMS/MMS Setting To Setup PTZ Preset Point 9To Setup Alarm SOPTo Setup CMS Setting To Setup POS Keyword Setting Missing, Suspicious Object, and Scene Change DetectedMissing Object Suspicious Object Enable MaskScene Change User Setting Visible Camera Remote Access TimePassword Confirm PasswordBackup Video Players 5678 Familiarizing QLogViewer ButtonsFamiliarizing the Player Buttons Chapter Function Keys Description Using Functional KeysUsing the Remote Programs Familiarizing the WebViewer Buttons Name Function To Setup Remote System Setting Camera Setting DisplayCamera Name Always Recording Familiarizing the WebViewer PTZ Buttons Emap Familiarizing the Remote Console ButtonsTo Setup Remote Console Setting LanguageRemote Server Channel Settings Using the Remote PlaybackTo Make a Selection Familiarizing the Local Playback Buttons To start playing the recorded video file Familiarizing the RealTime Playback Buttons Name Function Familiarizing the Download and Playback Buttons Using HandyViewer to Access DVR server Using PDAViewer to Access DVR ServerTo install PDAViewer thru ActiveSync To install PDAViewer from the Internet To Use the PDAViewer Using JavaViewer to Access DVR Server To Use the JAVAViewer Way down to select the Help file 104 Image Verification To Run the ImageVerification programClick Start Programs DSS ImageVerification Chapter IEnhance Name Function To Use iStable To Run Dispatch program Auto connect when starWeb Tools Dispatch ServerTo Add DVR server Remote SetupTo Setup Remote DVR Server Delete event and alarm log afterDelete recorded data after TV Out POSVirtual Keyboard Camera Display Camera SettingRecord Setting Main Configuration Network SettingUser Login Enable HandyViewer Network Schedule SettingAlarm Setting Launch E-Map To Setup Alarm Relay To Setup Send E-mail Setting Remote Backup Click Start Program DSS Tool Remote BackupTo back up the recoded data from the DVR server Page Page Using the Remote Control Server 5150 DVR Ddns Upload / Download Appendix a Network Service PortAppendix B Install PTZ through RS-232 Interface