Speco Technologies DVR-PC8 Series, DVR-PC16 Series PC Monitor Output, USB Ports, LAN Port, Mic

Page 10

10

3.1.6. PC Monitor Output

Connect PC monitor to view the image output. DVR-PC8 series supports both PC monitor and Spot monitor. When the analogue monitor is connected to RCA Jack, the part of analogue image is always outputted except for the various user interface shown in the PC monitor. The screen mode of the spot monitor output is always full screen, and is controlled independently with the PC monitor.

3.1.7. USB Ports

Connect exterior CD-RW with USB interface. Only approved USB CD-RW models by manufacturers can be used.

3.1.8. LAN Port

For remote monitoring, connect the network to LAN (Local Area Network), Internet, or exclusive line of TCP/IP basis. IP address should be fixed, and dynamic IP address allocated from DHCP cannot be used.

3.1.9. MIC

Input voice is synchronized to channel 1. When the voice signal is in line level, connect to line In jack above the MIC Input jack.

3.1.10. Speaker Output

The output signal is line level. To expand the output signal, there is a need for an amplifier.

3.1.11. Spot Monitor Output

When the analogue monitor is connected to BNC Jack, the part of analogue image is always outputted except for the OSD. The screen mode of the spot monitor output is always full screen, and is controlled independently with the PC monitor.

3.1.12. Image Input

Image input has analogue composite signal and can be set to NTSC or PAL, according to the requirement of the user during product order. Be sure to match the type of camera to be corresponding with the system. To get good quality image, check the power of the whole system and the safety of the ground construction. Also, adjust the lighting and focus iris of the camera properly.

3.1.13. Sensor Input / Alarm Output Port

To use sensor input and alarm output, alarm I/O Terminal (Option) would be needed. Connect cable of terminal to alarm output port, and then each sensor and wire of alarm devices to the corresponding terminal.

Note A sensor alarm is activated by a relay or switch. It can be connected to either N/O (Normal open) or N/C (Normal Close) type and the user has to set the sensor accordingly. The contact closure time of the switch or relay must be greater than 0.5 sec.

Image 10

Contents DVR-PC8/16 Series Electric Safety Signs of Caution and Warning Power Management Table of Contents Qty Contents DVR-PC8/16 SeriesDVR-PC8/16 Series Front Panel DVR-PC8 Series Back Panel DVR-PC16 Series Back PanelPTZ Port DVR-PC8 Series InstallationKeyboard Port Printer PortUSB Ports Sensor Input / Alarm Output PortPC Monitor Output LAN PortDVR-PC16 Series Installation Split Screen Mode Power ConnectionLogin Start ProgramStart Recording Recording SetupTo Start Recording Stop RecordingPage Search recorded image by Date Search Recorded ImageSearch recorded image by Time Main Screen NameCamera Channel Control Alarm OutputCurrent Recording Screen Split Screen ButtonDate / Time System InfoRemote Connection / Transmission Status Audio Input Indicator Sensor Event IndicatorRecording Status Indicator Search Recorded Image ViewerPan/Tilt Preference Settings PTZ SettingPreset Zoom In/OutTour Preset NameAuto WiperEvent Log Remote loginTools Play AudioViewer DVR LocationTime Position Indication Bar Searched ScreenBookmark Indicating Date / TimeSearch Calendar See an image in detail 1-screen modeAdjust Playback Speed Select Split ScreenStill Image / Minutes Backup Adjust Audio PlaybackMedia Backup ConfigurePanorama Sensor EventAdjust Picture Quality DeinterlaceSearch Tools SmartSearchChannel Information Play-back WindowCurrently Searched Date and Time Search Area Section SquareGo to Start SearchEnd Time Quick SearchSave Screen Search ListAPP Basic Method to Use the APP APP Screen LayoutInformation Menu FileEdit PreviewProcessing Modules ResetPost-processed STAdaptive DenoiseSharpen Auto Contrast EnhanceSharpen Convolution Edge-Sensitive DeinterlaceBackup Save Searched Image Still Image BackupVideo Backup PrintingConfigure Add Printer Search OptionWatch Mode Camera SettingSelect Security Screen/Watch Mode Security Screen Mode Selecting CameraWeekend Recording Function Camera LocationSimple Recording Time Schedule Time Range Current Recording ViewRecorded Video Quality Motion Detection AreaCover Entries Area Motion Detection SensitivityNetwork Auto Disconnect on no activity after Setup of Port RangeRemote Connection Time Limit Additional Network Options Bandwidth LimitRemote Event Notification Transmission Time LimitSensor/Control Enable Sensors and ControlsSensor Time Cameras Associated with Selected Sensor PTZ PresetSelect Sensor External Output connected to each SensorSound Use Recording ModeSensor Etc Display mode freezes after sensor Motion SensorUse the External Output No.2 Recording Failure AlarmVideo loss Detection Use the External output No.1Use PTZ Enable PTZPTZ Select CameraCurrent View Add PTZ ProtocolPort Camera AddressFocus Far Zoom OutFocus Near Iris OpenSet Camera PowerRegistered Accessory Information LocationPump AlarmLight FanColor Password Protected Recording Recording Enable/Disable Camera RecordingDisplay Import User ManagementRemove ExportUse Graphic Equalizer Recording ResolutionAudio/Graphic Equalizer/Select Language Use Audio Select LanguageCamera Sequence Selection To select 4-Split Screen ModeDisplay Division ClearAutomatic Alternation Mode FPS Setting per Camera FPS/ResolutionFPS and Resolution Setting per Camera System Recording PerformanceRecord Option ScheduleUse Schedule CopySensor-Activated S Motion DetectionMContinuousC FrameAdd Holiday Add/EditUpgrade SystemRequire Authentication Notify by E-mail When Sensor Event OccursSetting E-mail Send ToReset Configuration Export/ImportDigital Deterrent VCR Mode Instant PlaybackWhen buttons are pressed When button are pressedRewind VCR Playback and Record ModePlay or Pause Stop Fast ForwardRecord Camera Select multi-channels VCR Record Mode VCR Playback Mode Pin Assignment of Alarm Port AppendixTCP/IP Port Setting Method using the firewall Block Diagram for Alarm Input