Transition Networks CSDTF1022-100 instruction manual Installation, Cable Specifications

INSTALLATION

CAUTION: Wear a grounding device and observe electrostatic discharge precautions when setting switch and when installing Media Converter Slide-in- Module in the Media Conversion Center. Failure to observe this caution could result in damage to, and subsequent failure of, the Media Converter Slide-in- Module.

Set Loopback Test Switch

NOTE: The Loopback Test switch, located on Media Converter Slide-in-

Module front panel, allows the network administrator
to enable a loopback test for installation and network	Loop
debug procedures.

Use small flatblade screwdriver or similar device to set recessed switches. Refer to drawing for switch locations.

Set 3-Position Jumper

NOTE: Jumper is located on Media Converter Slide-in-Module circuit board.

CABLE SPECIFICATIONS

Fiber Cable

Bit error rate: ≤ 10-9

MULTIMODE

Fiber Optic Cable Recommended:	62.5 / 125 µm multimode fiber
Optional:	100 / 140 µm multimode fiber
	85 / 125 µm multimode fiber
	50 / 125 µm multimode fiber
CSDTF1011-100	850 nM
Fiber Optic Transmitter Power:	min: -14.0 dBm	max: -12.0 dBm
Fiber Optic Receiver Sensitivity:	min: -25.0 dBm	max: -12.0 dBm
Typical Maximum Cable Distance*:	2 kilometers
CSDTF1013-100	850 nM
Fiber-optic Transmitter Power:	min: -14.0 dBm	max: -12.0 dBm
Fiber-optic Receiver Sensitivity:	min: -25.0 dBm	max: -12.0 dBm
Typical Maximum Cable Distance*:	2 kilometers

Use small needle-nosed pliers or similar device to set jumper. Refer to drawing for jumper positions.

HARDWARE Converter mode is determined by 4-position switch settings below.

SOFTWARE Converter mode is determined by most- recently-saved on-board microprocessor settings.

Set MDI/MDI-X Switch

H S

HARDWARE MODE

H S

SOFTWARE MODE

SINGLEMODE
Fiber Optic Cable Recommended:	9 µm singlemode fiber
CSDTF1012-100	1300 nM
Fiber-optic Transmitter Power:	min: -21.0 dBm	max: -14.0 dBm
Fiber-optic Receiver Sensitivity:	min: -25.0 dBm	max: -14.0 dBm
Typical Maximum Cable Distance*:	8 kilometers
CSDTF1014-100	1300 nM
Fiber-optic Transmitter Power:	min: -21.0 dBm	max: -14.0 dBm
Fiber-optic Receiver Sensitivity:	min: -27.0 dBm	max: -14.0 dBm

NOTE: The MDI/MDI-X switch, located on Media Converter Slide-in-Module circuit board, allows the network administrator to use straight-through cable in installations where crossover-configuration cable is required.

Use small flatblade screwdriver or similar device to set recessed switches. Refer to drawing for switch settings.

Typical Maximum Cable Distance*:	8 kilometers
CSDTF1015-100 (long haul)	1300 nM
Fiber-optic Transmitter Power:	min: -15.0 dBm	max: -5.0 dBm
Fiber-optic Receiver Sensitivity:	min: -27.0 dBm	max: -14.0 dBm
Typical Maximum Cable Distance*:	15 kilometers
CSDTF1022-100 (long haul)	1300 nM
Fiber-optic Transmitter Power:	min: -15.0 dBm	max: -5.0 dBm
Fiber-optic Receiver Sensitivity:	min: -25.0 dBm	max: -14.0 dBm

MDI

Twisted		1	RTIP	TTIP	Twisted
Pair	#1	2	RRING	TRING	Pair	#1
Twisted		4	TTIP	RTIP	Twisted
Pair	#2	5	TRING	RRING	Pair	#2

Connectors for unlike devices

Set 8-Position Switch

		MDI-X
1
	RTIP		RTIP
2	RRING		RRING
4	TTIP		TTIP
5	TRING		TRING

Connectors for like devices

Typical Maximum Cable Distance*: 15 kilometers

*Actual distance dependent upon physical characteristics of network installation.

NOTE: The eight-position switch, located on Media Converter Slide-in- Module circuit board, allows the network administrator to configure the media converter for network conditions.

Use small flatblade screwdriver or similar device to set recessed switches for site installation. Refer to drawings at right for eight-position switch settings.