Transition Networks CSDTF1022-100 instruction manual Compliance Information

Page 1

COMPLIANCE INFORMATION

UL Listed

C-UL Listed (Canada)

CISPR22/EN55022 Class A + EN55024

CE Mark

FCC Regulations

This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at the user’s own expense.

Canadian Regulations

This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out on the radio interference regulations of the Canadian Department of Communications.

Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la class A prescrites dans le Règlement sur le brouillage radioélectrique édicté par le ministère des Communications du Canada.

European Regulations

Warning

This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

Achtung !

Dieses ist ein Gerät der Funkstörgrenzwertklasse A. In Wohnbereichen können bei Betrieb dieses Gerätes Rundfunkstörungen auftreten, in weichen Fällen der Benutzer für entsprechende Gegenmaßnahmen werantwortlich ist.

Attention !

Ceci est un produit de Classe A. Dans un environment domestique, ce produit risque de créer des interférences radioélectriques, il appartiendra alors à l’utilsateur de prende les measures spécifiques appropriées

T1/E1 Twisted-Pair Copper to Fiber

Slide-In-Module Media Converters

CSDTF10xx*-100

USER’S GUIDE

TRANSITION Networks CSDTF10xx-100 series media converters, designed to be installed in a PointSystemConversion Centerchassis, encode and decode T1 or E1 twisted-pair copper signals over duplex fiber-optic cable to extend the distance and transmission reliability of high speed T1 or E1 data traffic.

CSDTF1011-100

 

 

 

 

 

 

 

 

 

 

 

Provides an RJ-45 twisted pair copper

 

 

 

 

 

 

 

 

 

 

 

connector for T1 or E1 signals and a set

 

 

 

 

 

 

 

 

 

 

 

of RX/TX ST connectors to 850 nm

 

 

 

PWR

PWR

 

 

LNK

PWR

 

 

 

 

SDC SDF PWR

LKS

LKS

SDC SDF PWR

LA

PWR

LKS

SDC SDF PWR

LKS

multimode duplex fiber-optic cable.

DB-

RXF

 

LKM

LKM

 

RXF

D

LKM

TX

LKM

TX

 

 

 

 

E

 

 

 

 

LOOP

 

 

LOOP

 

 

 

LOOP

 

 

9

RXC

LKC

TX

TX

 

RXC

COL

TX

 

TX

 

 

 

 

TX

 

Link Alert

 

 

 

 

 

Singlemode

Singlemode

 

 

Singlemode

 

Singlemode

CSDTF1012-100

 

 

 

 

10BASE

 

RX

SET

 

 

TX

TX

 

-T

 

TX

TX

 

 

 

RX

RX

RX

 

RX

 

RX

 

 

RX

 

Multimode

Multimode

 

 

Multimode

 

Multimode

Provides an RJ-45 twisted pair copper

 

 

 

 

10BASE

50‰

 

 

 

 

 

 

 

0

 

 

 

 

 

 

 

 

 

 

 

 

 

 

connector for T1 or E1 signals and an

 

 

 

RX

RX

 

-2

 

RX

 

RX

 

CSDTF100

CFMFF100

CFMFF100

CFETF100

CECF100

CFMFF100

CFETF110

CFM

RX/TX ST connector to 1300 nm singlemode duplex fiber-optic cable.

CAUTION: RJ connectors are NOT INTENDED FOR CONNECTION TO THE PUBLIC TELEPHONE NETWORK. Failure to observe this caution could result in damage to the public telephone network.

Der Anschluss dieses Gerätes an ein öffentlickes Telekommunikationsnetz in den EG-Mitgliedstaaten verstösst gegen die jeweligen einzelstaatlichen Gesetze zur Anwendung der Richtlinie 91/263/EWG zur Angleichung der Rechtsvorschriften der Mitgliedstaaten über Telekommunikationsendeinrichtungen einschliesslich der gegenseitigen Anerkennung ihrer Konformität.

CSDTF1013-100

Provides an RJ-45 twisted pair copper connector for T1 or E1 signals and an RX/TX SC connector to 850 nm multimode duplex fiber-optic cable.

CSDTF1015-100 (long haul)

Provides an RJ-45 twisted pair copper connector for T1 or E1 signals and an RX/TX SC-LHconnector to 1300 nm singlemode duplex fiber-optic cable.

CSDTF1014-100

Provides an RJ-45 twisted pair copper connector for T1 or E1 signals and an RX/TX SC-SMconnector to 1300 nm singlemode duplex fiber-optic cable.

CSDTF1022-100 (long haul)

Provides an RJ-45 twisted pair copper connector for T1 or E1 signals and an RX/TX ST connector to 1300 nm singlemode duplex fiber-optic cable.

Trademark Notice

All registered trademarks and trademarks are the property of their respective owners.

Copyright Restrictions

© 2001, 2002 TRANSITION Networks.

All rights reserved. No part of this work may be reproduced or used in any form or by any means – graphic, electronic, or mechanical – without written permission from TRANSITION Networks.

Printed in the U.S.A.

33201.C

*In CSDTF10xx model designation, 10 represents the T1 or E1 RJ-45 connector;

xxrepresents the selectable fiber connector installed on the media converter.

CSDTF10xx in the Network . .

. . . . .2

Installation

. . . . .3

Operation

. . . . .7

Fault Isolation and Correction

. . . . .8

Cable Specifications

. . . .10

Technical Specifications

. . . .11

Compliance Information

. . . .12

Image 1
Contents Compliance Information Features Technical SpecificationsCSDTF10xx in the Network Declaration of ConformitySwitch-Selectable Configurations Cable SpecificationsSwitch-Selectable Functions Twisted-Pair Copper CableCable Specifications InstallationIs the PoWeR LED on the media converter illuminated? Fault Isolation and CorrectionIs the SDF Signal Detect/Fiber LED illuminated? Is the SDC Signal Detect/Copper LED illuminated?Operation Installation