Winegard WI-DM54, WI-DM04 owner manual Trouble Shooting, Things YOU Need, Installation & Assembly

TROUBLE SHOOTING

	1.	Be sure you have a clear line of sight. The signal from the satellite(s)
Antenna Reflector at 900		WILL NOT pass through trees, buildings,mountains etc. Remember
		the antenna has a 240 offset, this means that when the antenna is
		straight up and down, (900) it is looking 240 into the sky. See Fig. 2.
	2.	Do you have the TV set tuned for the correct channel 3 or 4
		(same channel as output of receiver)?
	3.	Have you entered the correct zip for the area you are currently in?
240 look angle		If the zip code is wrong, the antenna will be looking in the wrong
		direction or at the wrong elevation for the satellite signal you want.
LNBF	4.	Check connections at receiver, TV, and antenna.
	5. Check the TV. Does it receive pictures from off-air TV stations/VCR?
	6.	Retune system for best picture, using procedure on page 3.
	7.	Inspect antenna. Make sure that it has not been damaged. If antenna
		is even slightly bent, the receiver may not receive any signal.
	8.	Contact Dealer or Winegard Service Department.

FIGURE 2

ANTENNA DOES NOT ROTATE, OR IS HARD TO ROTATE

1.Inspect antenna on roof. Make sure that mount has not been damaged.

2.Check for caulking between gear housing and baseplate.

3.Be sure cables are not binding, and that they are installed properly.

4.Contact Dealer or Winegard Service Department.

ANTENNA DOES NOT RAISE, OR IS HARD TO RAISE

1.Inspect antenna on roof. Make sure that mount has not been damaged.

2.Check for caulking on elevating shaft.

THINGS YOU NEED

Screwdrivers (Phillips and slot)	ABS glue	Non-hardening sealant
1-3/4" hole saw	Drill w/1/8" bit	(Check manufacturer’s specifications for
7/16" wrench	Tape measure	compatibility with your roof material)

Winegard's Digital Elevation Sensor has been

INSTALLED and CALIBRATED at the factory.

INSTALLATION & ASSEMBLY

STEP 1. Choose a location on the roof for dish that will allow dish to raise and rotate without interfering with other roof-mounted equipment. Make sure inside ceiling plate is easily accessible, and with no obstructions that would interfere with operation.

Figure 3 shows minimum distance (10") antenna should be located from edge

of vehicle roof. It is recommended that you check with your dealer or manufacturer

FIGURE 3 for provisions that may have been made in the roof for antenna mounting; a reinforced roof area, or pre-wire installation from the factory.

NOTE: The system must be level for proper operation. Winegard Model

RW-5000 roof wedge with gasket is available.

If inside roof wedge is needed, Winegard’s

RW-1000 can be trimmed to fit ceiling plate.

	STEP 2. Position template on roof (pg. 8 this manual).
	CAUTION: DO NOT drill through wiring.
	Carefully drill a 1-3/4"hole through roof and
CenterRoof	ceiling of vehicle. Inspect hole to make sure wiring
	is intact. (Roof template, pgs. 8-9.)
Line	It is highly recomended that the antenna be
	mounted on roof center line. Do not mount
	antenna closer than 10" from edge of roof.

4.Contact Dealer or Winegard Service Department.

LCD DISPLAY CODES

HL	High Limit
LL	Low Limit
Lo	Battery Low
Er	Communication Error
— —	Initializing

NOTE: Initialization may take up to 5 seconds.

Based on 5 minutes a day of usage, standard new alkaline batteries should last 88 days.

19.50”

34” DIAMETER

OPERATING

AREA

17” RADIUS

26”

RW-5000 Roof Wedge w/gasket

MINIMUM

10”

Vehicle Roof

	Antenna Controls	Interior
FRONT OF VEHCILE		Roof Wedge
	NOT TO SCALE	(optional)

4 5