Digital Elevation Sensor Interior Wallplate

DIGITAL ELEVATION SENSOR INTERIOR WALLPLATE

Step 12. See Figure 14. If using the SM-1000 surface mount box,			Figure 14
feed cable through hole in box.		Cable and plug
STEP13: Connect wires coming from sensor on		from roof sen-
STEP13: Connect wires coming from sensor on		sor unit; plugs
roof to wall plate display in vehicle. It is important		into sensor
to properly connect the wires at the roof and the		readout cable.
wall plate. (Plug will click when inserted properly.)
The system is designed to use a 9 volt battery
OR +12 VDC from vehicle. Do not use both!
Improper wiring will cause
damage to the product.	SM-1000 Surface Mount Box		Sensor to readout cable

Readout assembly

STEP 14: Pressing the button when the antenna is in a vertical position should display 24 (±1°). Display will automatically turn off after 1 minute.

STEP 15: Check connectors and cable entry points. Be sure these areas are properly sealed to prevent water damage.

PARTS LIST

BACK VIEW

(2)1/4-20 Hex Nut

Backup Frame

(2) E-Clip for 1/4" Pin

Plastic Plug

O-Ring

RP-4400	Worm Gear

(2) 1/4" x 3.25 Pin

Spacer

OPERATION (Also on pages 2-3)

STEP 16: Using satellite receiver, find correct elevation for your location. See the receiver manual for details of setup information.

STEP 17: Press button on Winegard digital display wall plate. If antenna is in travel position, the display will show LL for Low Limit.

STEP 18: Crank elevation handle to raise antenna. Stop when readout displays correct elevation for your location.(Found on receiver setup menu.)

STEP 19: Rotate antenna VERY SLOWLY until correct satellite

signal is acquired. NOTE: Rotate 3° and stop. DO NOT rotate

continuously even if your are rotating slowly. If the elevation angle has changed, it could be due to the following —

•Vehicle is not parked level.

•Antenna system mounted on slightly sloped roof. If

this is the reason, after you have rotated the antenna to the appproximate correct compass direction, adjust to correct elevation and continue search.

Screw

P.N. 2160196

Pivot Shaft

Part of

RP-30RM kit

Spring

Seal

Part of

RP-30RM kit

Cast Aluminum

Gear Housing

Turret

P.N. 3100728

Pivot Bearing

Part of

RP-30RM kit

Special Notes: When you have found the satellite signal, adjust the antenna up/down and right/left for the strongest signal your receiver displays. Due to variation in receivers and installation methods, you may find the elevation numbers after peaking on strongest signal no longer match what the receiver display recommended. This is normal. The elevation sensor should always get you close enough to pick up a signal to peak on. If display turns off while you’re searching, just push button for another minute of operation. With a little practice, most users find the signal in 30 to 50 seconds.

Cutaway view of mount/gear housing

Rotate Limit

Plate

P.N. 3720052

Screw

P.N. 2160197

Elevating Gear Part of RP-30RM kit

Outer Bearing

P.N. 2590347

Replacement Parts

DISPLAY CODES
HL	High Limit
LL	Low Limit
Lo	Battery Low
Er	Communication Error
— —	Initializing

NOTE: Initialization may take up to 5 seconds.

Figure 6

*CAUTION: DO NOT connect to +12 VDC if using a 9 volt battery.

Snap battery in place, making sure battery terminals are firmly seated on wall plate terminals.

Turret Base P.N. 3100730

Vent Tube P.N. 2200122

Elevate Shaft

Gear

P.N. 2200465

Inner Bearing P.N. 2590348

Hub

P.N. 3100736