Marshall electronic V-R102DP-HD Switch Settings, Adjustments and Indicators, Operational Setup

8Switch Settings, Adjustments and Indicators

Tally Lamps

V-R102P-HD

Dry Erase

Screen aspect ratio switch 4:3 or 16:9 selector and indicators	Image Adjustment Controls
	Note: Tint only functions when NTSC
	Video or S-Video are selected

5Mechanical Specifications

Dimensions	19.12” w x 8.67” h x 1.5” d (485.7mm x 220.22mm x 38.1mm)
V-R82DP-HD Weight	5.5 lbs (2.4 kg)
V-PS12-5V-1 Power Supply Weight	1 lbs (0.45kg)

6Operational Setup

1.Unpack the V-R102DP-HD and accompanying V-PS12-5V-1 power supply. Physically inspect for any damage that may have occurred during shipping. Should there be any damage, immediately contact Marshall Electronics at 800-800-6608.

If you are not located within the continental United States call +1 310-333-0606.

2.After inspection, install in your desired location of a standard EIA 19-inch equipment rack. Adequate ventilation is required when installed to prevent possible damage to the V-R102DP-HD internal components.

3.Connect required cables for signal input and output. Please note that power must be applied to the V-R102DP-HD for all outputs to be activated. All BNC connectors should be rated for 75Ω.

4.Plug the V-PS12-5V-1 power supply into the A.C. source

5.Attach twist lock power connection from V-PS12-5V-1 power supply to the back of the unit.

6.Turn on each of the V-R102DP-HD screens by depressing the power switch located on the front of the unit for each screen.

7Connectors

* HDSDI/SDI Inputs comply to SMPTE-259M, 292M, SDI-270Mbs , HDSDI-1.485 Gb/s				Tally IN
* Component Inputs comply to SMPTE274M, 294M,295M,296M				DB-15 Female
				Pin1-M2Yel	Pin9-
* Composite Video Inputs comply to SMPTE-170M
* Tally lamps active when connected to ground				Pin2-M2Red	Pin10-
				Pin3-M2Grn	Pin11-M1Yel
				Pin4-	Pin12-M2Red
				Pin5-Gnd	Pin13-M3Grn
				Pin6-	Pin14-
				Pin7-	Pin15-Gnd
S-Video Out	S-Video In
	4 Pin Din (Female)	4 Pin Din (Female)
	Pin1 - GND	Pin1 - GND
	Pin2 - GND	Pin2 - GND	12 VDC from
	Pin3 - Yout	Pin3 - Yin	V-PS12-5V-1 power supply
	Pin4 - Cout	Pin4 - Cin	Left Pin - Pos
			Right Pin- Neg

Active Outputs require power to be applied

All input signals appear as output signal

Analog output signals are buffered and amplified

DVI-I Connector

Pin# Signal Pin# Signal

4:3 Aspect 16:9 Aspect

VGA/XGA Connector

PIN#	SIGNAL	PIN#	SIGNAL
1	RED	9	NC
2	GREEN	10	NC
3	BLUE	11	NC
4	NC	12	NC
5	GND	13	HSYNC
6	RED SHIELD	14	VSYNC
7	GREEN SHIELD	15	NC
8	BLUE SHIELD

1	T.M.D.S DATA 2-	16	HOT PLUG DETECT
2	T.M.D.S DATA 2+	17	T.M.D.S DATA 0-
3	T.M.D.S DATA 2/4	18	T.M.D.S DATA 0+
	SHIELD
4	T.M.D.S DATA 4-	19	T.M.D.S DATA 0/5
			SHIELD
5	T.M.D.S DATA 4+	20	T.M.D.S DATA 5-
6	DDC CLOCK	21	T.M.D.S DATA 5+
7	DDC DATA	22	T.M.D.S CLOCK
			SHIELD
8	ANALOG VERT. SYNC	23	T.M.D.S CLOCK+
9	T.M.D.S DATA 1-	24	T.M.D.S CLOCK-
10	T.M.D.S DATA 1+
11	T.M.D.S DATA 1/3	C1	ANALOG RED
	SHIELD
12	T.M.D.S DATA 3-	C2	ANALOG GREEN
13	T.M.D.S DATA 3+	C3	ANALOG BLUE
14	+5V POWER	C4	ANALOG HORZ SYNC
15	GND	C5	ANALOG GROUND

6 VV--R102DPR82DP--HDUsersGuide MarshallElectronics 3