FUNAI 6842PE owner manual Sylvania Limited Warranty, Duration, Limits and Exclusions, Tel

Page 28

SYLVANIA

LIMITED WARRANTY

FUNAI CORP. will repair this SYLVANIA product, free of charge in the USA in the event of defect in materials or workmanship as follows:

DURATION:

PARTS: FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the date of original retail purchase. Three (3) years for Plasma Panel. Certain parts and Plasma image burn-in are not covered under this warranty.

LABOR: FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date of original retail purchase.

LIMITS AND EXCLUSIONS:

THIS WARRANTY IS EXTENDED ONLY TO THE ORIGINAL RETAIL PURCHASER. A PURCHASE RECEIPT OR OTHER PROOF OF ORIGINAL RETAIL PURCHASE WILL BE REQUIRED TOGETHER WITH THE PRODUCT TO OBTAIN SERVICE UNDER THIS WARRANTY.

This warranty shall not be extended to any other person or transferee.

This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing or if service was attempted by an unauthorized service center. This SYLVANIA Limited warranty does not apply to any the product not purchased and used in the United States.

This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product not supplied by FUNAI CORP., or damage which results from accident, misuse, abuse, mishan- dling, misapplication, alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this product or damage which results from fire, flood, lightning or other acts of God.

THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.

FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE USE OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY AND FIT- NESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS REPRESEN- TATIVES IN THE UNITED STATES.

ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY A FUNAI AUTHORIZED SERVICE CENTER. THIS WARRANTY IS ONLY VALID WHEN THE UNIT IS CARRIED-IN TO A FUNAI AUTHORIZED SERVICE FACILITY.

THE PRODUCT MUST BE ACCOMPANIED BY A COPY OF THE ORIGINAL RETAIL PURCHASE RECEIPT. IF NO PROOF OF PURCHASE IS ATTACHED, THE WARRANTY WILL NOT BE HONORED AND REPAIRS COSTS WILL BE CHARGED.

IMPORTANT:

THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE. IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE UNABLE TO OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI CORP.

ATTENTION:

FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PROD- UCT WITHOUT PRIOR NOTICE.

To locate your nearest SYLVANIA Authorized Service Center or general service pro- cedure, please call 1-800-605-8453 or write to the following:

FUNAI CORPORATION, INC.

SERVICE CENTER

19900 Van Ness Avenue, Torrance, CA 90501

Tel :1-800-605-8453

http://www.funai-corp.com

Head Office: 100 North Street, Teterboro, NJ 07608

PLEASE DO NOT SHIP YOUR UNIT TO THE TETERBORO ADDRESS.

Printed in Malaysia

1EMN20088

 

L0601UB★★★★★

Image 28
Contents Plasma Display Important Safety Instructions Instructions Important Safety# Caution Contents Inserting the Remote Control Batteries Supplied AccessoriesRemote Control Range Main Unit Component NamesFront Rear Names Remote ControlComponent Power Operating the Plasma DisplayBasic Operations Input SelectSelecting the Input Signal Displaying the Current Input SignalSelecting the Input Signal DisplayChanging the Aspect Ratio Screen Mode Screen ModeStill Sleep Plasma DisplayStill SleepNavigating the SET UP Menu Layout of the Setup MenuEntering the Main Menu Picture SelectDisplay MenuManually Adjusting the Picture Settings Automatically Adjusting the Picture SettingsInitializing the Adjustments Window Setting Switching the Display LanguageSetting the Screen Saver Setting the Screen Saver and the Background ColorSetting the Background Color External Input Terminals Operating the Plasma Display / External Input TerminalsConnecting Devices to the AV Input Terminals Video Signal Connection Basic Signal TransferVideo Signal Connection Better Signal Transfer External Input TerminalsTerminals Connecting Devices to the Component Input TerminalsExternal Input Connecting Plasma Display to Audio System Connecting the Power CableAudio Signal Connection Attaching a Wall Mount Bracket Sold Separately Cleaning the Plasma Display MaintenancePreventing Image Burn on the plasma display Troubleshooting Guide Maintenance / Warning / Troubleshooting GuideTroubleshooting Guide About Interference to Infrared DevicesAbout Pixel Defects Check These Items and TRY These CorrectionsSpecifications Troubleshooting Guide / SpecificationsInstalación DE LAS Pilas EN EL Control Remoto Referencia Rápida EN EspañolTraslado de la unidad principal Unidad Principal Nombres DE LOS ComponentesControl Remoto Sylvania Limited Warranty DurationLimits and Exclusions Tel