FUNAI CIWL3706 owner manual Initial Settings, Language Selection, Autoscan TV/DTV, Autoscan Catv

Page 12

INITIAL SETTINGS

Hint: Before starting initial setup you must connect antenna.

INITIAL SETTINGS

This section describes the initial settings when you first turn on the power after purchase. The initial setting items are shown below.

• LANGUAGE SELECTION

You can select the menu language displayed on the screen among English, Spanish and French.

AUTOSCAN (TV/DTV)

(Select “Air” when using antenna)

The channels broadcasted in TV and DTV are automatically scanned and memorized. Only the receivable channels in the area where this TV is used will be memorized.

AUTOSCAN (CATV)

(Select “Cable” when using RF/Incoming cable) The channels broadcasted in CATV are automati- cally scanned and memorized.

POWER

SLEEP

INPUT

SELECT

1

2

3

4

5

6

 

 

AUDIO

7

8

9

 

 

STILL

-

0

 

SETUP

 

SCREEN

 

MODE

 

 

ENTER

BACK

 

INFO

1After making all the necessary connections, turn on this TV.

2Press [POWER]. Initial Setup menu will appear.

This operation may take a few moments.

If Initial Setup menu does not appear, press and hold [ENTER] for 3 seconds, initial setup will appear then proceed to step 3. If you have already turned on this TV before, refer to “LAN- GUAGE SELECTION” on page 17 to select a language for the on-screen displays.

12

3Select your language using [K/L], press [ENTER].

When you first turn on the power, the following screen is displayed.

InitialI i i l Setup

Select the language for setup display.

English

Elija idioma de preparación.

 

Español

Sélectionner langue écran config.

Français

Select

ENTER Enter

SETUP

Exit

The Antenna Confirmation will be displayed in the selected language after you press [ENTER].

4Select source of ANT. IN jack using [K/L], press [ENTER].

InitialI i i l Setup

Make sure the antenna is connected to "ANT IN" jack.

Air

Select the destination of "ANT IN" jack.

 

Cable

 

 

 

Air

 

 

 

Cable

Or

 

 

 

ANT IN

 

 

Select

BACK

Back

SETUP

ENTER Enter

Exit

5Autoscan will start automatically.

InitialI i i l Setup

Now the system is scanning for channels,please wait.

5%

Analog channels

1ch

 

 

 

 

 

 

Digital channels

0ch

 

 

 

 

 

 

 

SETUP

Exit

When scanning has completed, the lowest memorized channel will be displayed.

NOTES:

The initial Autoscan function can be executed for either “Air” or “Cable” only once. When you change the connection (Air/Cable), set the “Autoscan” again. (Refer to page 13.)

If you connect cable system directly, contact the CATV installer.

When the scanning is not completed, Helpful Hint will be displayed every time you turn on the power. If you have previously registered channels when this screen appears you can select a channel with number buttons.

2-0

No channel is registered.

Press and hold "ENTER" key for 3 seconds.

Contact support hotline provided on manual or back of unit.

Sin canal registrado.

Mantenga oprimida la tecla "ENTER" durante 3 segundos.

Llame teléfono de apoyo en manual o atrás de TV.

Pas de chaîne consign.

Maintenir la touche "ENTER" pressée 3 secondes.

Contacter numero d'urgence dans manuel ou arrière appareil.

Support hotline is provided on the front page of this manual.

EN

Image 12
Contents Inch Important Safeguards Precautions Important Safeguards / PrecautionsDealer Purchase from Supplied Accessories FeaturesDTV/TV/CATV ChipContents Functions Remote CONTROL,TOP and Rear Panel Function Installing the Batteries Battery PrecautionsFunctions Digital Audio OUTPreparation for USE Connection Antenna Cable ConnectionConnection to CABLE/SATELLITE BOX External Connection Hdmi ConnectionComponent Connection Video ConnectionAnalog AUDIO/VIDEO Connection Audio Output ConnectionInitial Settings Initial SettingsLanguage Selection Autoscan TV/DTVChannel Settings Autoscan Initial Settings / Channel SettingsPress Enter To exit the setup, press Setup Channel ListChannell Listi Channel Settings Select Register with Enter To exit the setup, press SetupManual Register Manual l RegisterAntenna Confirmation AntennaPress Enter To exit the setup, press Setup Language SelectionLanguage Volume Adjustment Watching TV Channel SelectionNtsc AtscStill Mode Switching AudioSwitching External Input When using VIDEO2 or S-VIDEO2 input jackWhen using COMPONENT1 input jacks When using COMPONENT2 input jacksSidebar FullCinema WideScreen Information To clear the display, press Back or Info againBuffy Vampire i Slayer l Sleep Timer Optional Settings Setup ScreenWatching TV / Optional Settings Refer to Language Selection onPicture Adjustment Caption Mode CC1 and Text1 Closed CaptionCC3 and Text3 CC2, CC4, Text2 and Text4Service 1 to Service DTV Closed CaptionClosed Caption Style OffOptional Settings Press Enter Password entry screen is displayed See the following description for setting each itemChip Selection NC-17PG-13 TV-MA Mature audience only TV-14New Password Chipip Enter password Confirm passwordHdmi Audio Set the method of sound input for Hdmi jackMiscellaneous Troubleshooting Guide Miscellaneous Maintenance GlossarySpecifications Miscellaneous / SpecificationsVHF UHF CatvWarranty Statement Regarding NON Authorized Repairs DurationLimits and Exclusions