FUNAI TB100HH9 owner manual Connections, Connecting to a TV without A/V Jacks, White red Yellow

Page 10

Connections

1Disconnect the AC power cords of the devices from the AC outlet.

Desconecte los cables de alimentación de los aparatos del tomacorriente CA.

2Disconnect RF coaxial cable from antenna input jack of your TV.

Desconecte el cable coaxial de RF del conector hembra de entrada de antena de su televisor.

3Make the connections as illustrated below.

Efectúe las conexiones tal como se ilustra a continuación.

4Plug all AC power cords into AC outlets, then turn all devices on.

Enchufe todos los cables eléctricos de CA en los tomacorrientes de CA y conecte la alimentación de todos los equipos.

AConnecting to a TV without A/V Jacks

Conexión a un TV sin tomas de A/V

TV

TV antenna

Antena de TV

STB

RF cable (supplied)

cable de RF (se incluye)

BConnecting to a TV with A/V Jacks

Conexión a un TV con tomas de A/V

TV

TV antenna

Antena de TV

STB

white red

yellow

NOTE:

	yellow
white
red

Audio cable
cable de audio		Video cable
		Video cable
		cable de
		video

•If your TV has only one audio jack, connect the AUDIO OUT jack (L) (white) on the STB to the audio input jack on the TV.

Si su TV sólo tiene una toma de audio, conecte la toma AUDIO OUT (L) (blanco) del STB, a la toma de entrada de audio del TV.

10

EN

Image 10

Contents TB100HH9 Before Using Risk of Electric Shock Do not OpenInsert Precautions Important Copyright InformationBefore Using Advanced Operation B l e o f C o n t e n t sOverview Installing Batteries AccessoriesInformation on Digital Broadcasting Remote Control Location of ControlsRear Panel Remote control sensor Power indicatorFront Panel Video OUT jack yellowConnections Connecting to a TV without A/V JacksConnecting to a TV with A/V Jacks White red YellowRed Connecting to a Cable Box OptionalWhite EllowConnecting to Other Devices Red yellowPress STANDBY-ON on the remote control to activate the STB Initial Setup Setup WizardInitial Setup Appropriate Viewing ChannelSelect your time zone using K / L, then press OK Select Continue using s / B, then press OKSelect the language using K / L, then press OK Select Autoscan using K / L, then press OKAbout Sub-channel Broadcasting Basic OperationSelecting Channels on the STB Enter the main channel numberPress Still To cancel still modePress Audio repeatedly Choosing Audio LanguagePress EPG while watching TV Select the desired program using s / BPress Display Channel BannerAdvanced Operation Press SetupSelect ADD/ Delete using K / L, then press OK Autoscan Receiving ChannelsPress OK again to add the channel to the channel map Press Setup to exitSelect Delete using K / L, then press OK AddPress Setup Select Detail using K / L, then press OK Adjusting AntennaSelecting Display Mode SelectDISPLAY MODEusing K / L, then press OKPress Setup Select Time using K / L , then press OK Information on Display ModeSetting the Time Zone and D.S.T Daylight Saving Time Select Time Zone using K / L , then press OKEnter the password using the Number buttons Select D.S.T using K / L , then press OKSelect on or OFF using s / B , then press OK Chip OptionsThen press OK repeatedly to switch between view and block Select the desired rating type using K / L , then press OKSelect the desired rating using Mpaa RatingSelect NEW Password using K / L , then press OK Enter the new 4-digit password using the Number buttonsSelect Closed Caption using K / L , then press OK Press Setup Select Detail using K / L , then press OKSelect Manual using K / L , then press OK Closed Caption OptionsAuto Power Down Select desired amount of time using K / L , then press OKSelect CH3 in RF OUT menu Viewing Analog TVMethod 1 Método Select ch3 on your TVSelect the desired channel on your TV Method 2 MétodoSelect RF Through in RF OUT Press STANDBY-ON to activate the STBSelect RF OUT using K / L, then press OK Setting RF OUTUsing Setup to Switch RF OUT Setting Select the desired setting using K / L, then press OKTroubleshooting OthersSpecifications Limited Warranty Customer Service Tel