FUNAI TB100HH9 Press OK again to add the channel to the channel map, Press Setup to exit, Add

Page 19

Add

4With “ADD” selected, enter the main channel number you want to add, then press [OK] or wait for a few seconds to fix the number.

If the main channel number is 1 digit, press [0] first.

NOTE:

•Entering sub-channel number is not required.

5Press [OK] again to add the channel to the channel map.

E.g., adding channel 6

(or leave for

a few seconds)

ADD/DELETE		6.X
		6.X
EXIT
CHANNEL	ADD	6
CHANNEL		6
	DELETE	10
TIME		10
TIME		20
		20
DETAIL		58
INITIAL

E.g., adding channel 26.

(or leave for a few seconds)

ADD/DELETE		26.X
		26.X
EXIT
CHANNEL	ADD	6
CHANNEL		6
	DELETE	10
TIME		10
TIME		20
		20
DETAIL		26
INITIAL

•The selected channel is now added.

To continue adding:

Repeat steps 4 and 5.

6 Press [SETUP] to exit.

Delete

4Select “DELETE” using [ K / L], then press [OK].

ADD/DELETE		10.1
		10.1
EXIT
CHANNEL	ADD	10
CHANNEL		10
	DELETE	20
TIME		20
TIME		26
		26
DETAIL		56
INITIAL

5Select the channel number you want to delete from the channel list on the right using [ K / L], then press [OK].

E.g., deleting channel 26.

ADD/DELETE	26.1
ADD/DELETE

EXIT
CHANNEL	ADD	10
CHANNEL		10
	DELETE	20
TIME		20
TIME		26
		26
DETAIL		58
INITIAL

ADD/DELETE		58.1
		58.1
EXIT
CHANNEL	ADD	10
CHANNEL		10
	DELETE	20
TIME		20
TIME		58
		58
DETAIL		60
INITIAL

•The selected channel is now deleted.

To continue deleting:

Repeat step 5.

6 Press [SETUP] to exit.





	Operation	Advanced

19

EN

Image 19

Contents TB100HH9 Risk of Electric Shock Do not Open Before UsingInsert Important Copyright Information PrecautionsB l e o f C o n t e n t s Before Using Advanced OperationOverview Installing Batteries AccessoriesInformation on Digital Broadcasting Location of Controls Remote ControlVideo OUT jack yellow Remote control sensor Power indicatorFront Panel Rear PanelWhite red Yellow Connecting to a TV without A/V JacksConnecting to a TV with A/V Jacks ConnectionsEllow Connecting to a Cable Box OptionalWhite RedRed yellow Connecting to Other DevicesAppropriate Viewing Channel Initial Setup Setup WizardInitial Setup Press STANDBY-ON on the remote control to activate the STBSelect Autoscan using K / L, then press OK Select Continue using s / B, then press OKSelect the language using K / L, then press OK Select your time zone using K / L, then press OKEnter the main channel number Basic OperationSelecting Channels on the STB About Sub-channel Broadcasting Choosing Audio Language To cancel still mode Press Audio repeatedly Press StillChannel Banner Select the desired program using s / BPress Display Press EPG while watching TVAutoscan Receiving Channels Press SetupSelect ADD/ Delete using K / L, then press OK Advanced OperationAdd Press Setup to exitSelect Delete using K / L, then press OK Press OK again to add the channel to the channel mapSelectDISPLAY MODEusing K / L, then press OK Adjusting AntennaSelecting Display Mode Press Setup Select Detail using K / L, then press OKSelect Time Zone using K / L , then press OK Information on Display ModeSetting the Time Zone and D.S.T Daylight Saving Time Press Setup Select Time using K / L , then press OKChip Options Select D.S.T using K / L , then press OKSelect on or OFF using s / B , then press OK Enter the password using the Number buttonsMpaa Rating Select the desired rating type using K / L , then press OKSelect the desired rating using Then press OK repeatedly to switch between view and blockEnter the new 4-digit password using the Number buttons Select NEW Password using K / L , then press OKClosed Caption Options Press Setup Select Detail using K / L , then press OKSelect Manual using K / L , then press OK Select Closed Caption using K / L , then press OKSelect desired amount of time using K / L , then press OK Auto Power DownSelect ch3 on your TV Viewing Analog TVMethod 1 Método Select CH3 in RF OUT menuPress STANDBY-ON to activate the STB Method 2 MétodoSelect RF Through in RF OUT Select the desired channel on your TVSelect the desired setting using K / L, then press OK Setting RF OUTUsing Setup to Switch RF OUT Setting Select RF OUT using K / L, then press OKOthers TroubleshootingSpecifications Customer Service Tel Limited Warranty