Inserting batteries, On-Screen Help/Instructions

KV-27S40 / 27S45 / 27S65 / 29SL40 / 29SL40A / 29SL40C/ 29SL45 / 29SL65 / 29SL65C/ 29XL40M / 29XL40P / 29XT11A

Basic Set up

Inserting batteries

Insert two size AA (R6) batteries (supplied) by matching the + and – on the batteries to the diagram inside the battery compartment.

Notes

•Remove the batteries to avoid damage from possible battery leakage whenever you anticipate that the remote control will not be used for an extended period.

•Handle the remote control with care. Avoid dropping it, getting it wet, or placing it in direct sunlight, near a heater, or where the humidity is high.

•Your remote control can be programmed to operate most video equipment. (see page 26)

Using the remote control, Move & Select buttons

	MTS
TV DBS	GUIDE	Move
RESET	MENU

VOL CH

Select

CODE SET

The supplied remote control has "arrow" buttons (V, v, B, b) which allow for movement of the on-screen selector in four directions. Pressing on the outer buttons will cause the selector to move in the corresponding direction. Pressing the center button ( ) will select the item.

Adjustments bars

When menu items present an adjustment bar

( or ), use the arrow buttons to change the setting.

On-Screen Help/Instructions

Several menu windows will provide prompts and instructions to assist you in navigating through the different functions. When presented, use these to supplement the instructions in this manual.

Note

•To reset your TV to factory settings, turn the TV on. Then, while pressing the RESET button, press the POWER key on your TV. The TV will turn itself off, then back on. (except KV-20V80).

Using your New TV

Setting up the TV automatically

The Easy Setup Guide allows you to set the on-screen language and set all receivable channels. The Easy Setup Guide screen appears every time you turn on the TV until you perform AUTO PROGRAM.

TheEasySetupGuidefeaturedoesnotapplyfor installationsthatuseacableboxforallchannel selection.

To set up the TV manually, refer to “Using the SET UP menu” on page 23.

Tips z

•Performthisfunctionduringtheday,withtheantenna

and/orcableproperlyconnected,toensurethatallavailable

channelswillbebroadcastingandreceivable.

•AfterusingtheEasySetupGuideyouwillstillhavethe optionofadjustinganyofthesystemsettings,likeskipping channels,throughtheSETUPmenu(page24).

•TheTVmustbesettotheTVinputtoexecuteAUTO PROGRAM.PressANTuntilachannelnumberappears.

•IfyourcableorantennaisconnectedtoAUX,then pressANTuntilAUXappearsnexttothechannel number.(KV-27S65,27V65only)

Using the buttons on the front of the TV:

SET UP TV/VIDEO – VOLUME +

– CHANNEL + POWER

For KV-27V65, the control buttons are located on the top of the TV.

1Press POWER to turn on the TV.

The Easy Setup Guide screen appears.


POWER
ENGLISH:	[CH+]
ESPANOL:	[CH-]
AUTO SET UP:	[VOL+]
DEMO:	[VOL-]

First please	connect

cable/antenna. Press [SETUP]to exit

2(except Canadian models)

Press CH + to select English screens or CH – to select Spanish screens.

–CHANNEL +

3Press VOL + to continue or VOL – for a DEMO of functions and menus.

VOLUME

AUTO PROGRAM

AUTO PROGRAM appears and the TV starts scanning and presetting channels automatically. When all the receivable channels are stored, the lowest numbered channel is displayed. If the TV receives cable TV channels, CABLE is set ON automatically.

To perform AUTO SET UP again

•Press SET UP on the TV.

•Press CH + or CH – to select a language.

•Press VOL + to restore factory settings (CONTINUE TO AUTO PROGRAM? will appear on the screen). Press CH + to continue or CH – to exit.

•Press SET UP to exit.

Note

•When you perform AUTO PROGRAM, your CHANNEL FIX, CHANNEL BLOCK and ON/OFF TIMER settings will be erased.

— 12 —