RCA L26HD32D To connect a Hdmi or a DVI device to the unit, Not supplied To PC/DVI Audio, Tv/Dvd

Page 37

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Connections to other equipment

 

 

 

 

(continued)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

To connect a HDMI or a DVI device to the unit

The HDMI input receives digital audio and uncompressed video from a HDMI device or uncompressed digital video from a DVI device.

When you connect to a DVI device with a HDMI-to-DVI adapter cable, it transfers only video signal. Separate analog audio cords required.

Rear of the unit

To HDMI 1/DVI IN HDMI - to - DVI adapter cable

(HDMI type A connector)

 

 

(not supplied)

 

To PC/DVI AUDIO IN

 

To DVI output

 

 

Audio cord (not supplied)

 

 

 

or

HDMI cable (type A connector)

To HDMI 2 (or HDMI 1/DVI) IN

(not supplied)

To HDMI out

 

DVI device

HDMI device

NOTE:

•When you connect a DVI device, you must connect only with HDMI 1/DVI.

When using HDMI 1 to connect your HDMI or DVI devices, you must select the corresponding audio input source (HDMI or DVI) on the menu screen (see ”Selecting the HDMI audio input source” on page 24). Otherwise you will only see the image with no sound.

•If you connect an external component (cable box, satellite receiver, etc.) to this LCD TV using an HDMI cable or a DVI to HDMI cable, the image will not display if the output resolution of the component is set to 480i. To receive the picture you must change the output resolution on the external component.

Should you require further instruction, please contact the manufacturer of the external component.

Using an AV Amplifier with built-in digital surround

If you are using an Amplifier with built-in digital surround sound, you can enjoy various audio systems including Dolby Digital Surround audio that sounds just like the movie.

Connect an AV amplifier with built-in Dolby Digital decoder, DTS decoder, or MPEG decoder etc. as shown below.

Rear of the unit

Coaxial Digital

Audio Output

Coaxial digital cable (not supplied)

To Coaxial Digital Audio Input

AV Amplifier with built-in digital surround decoder as listed above

Front

Speaker

Subwoofer (Right)

TV/DVD

Front

Speaker

(Left)

 

Center Speaker

Surround

Surround

Speaker (Left)

Speaker

 

(Right)

NOTE:

• When you are viewing digital broadcast, this unit will not work in conjunction with DTS audio or MPEG audio. There will be no sound output if connected to an AV amplifier with a built-in DTS decoder or MPEG decoder.

• Coaxial digital audio output is active only when receiving digital broadcasting, not when receiving analog broadcasting.

37

51F0101A_eng.indd 37

3/10/08 10:56:11 AM

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Digital Television Transition Notice L26HD32D L32HD32DLocation of the required Marking Qualified Service PersonnelS3126A Important Safety InstructionsCondensation HOW to Handle the LCD PanelSafety Precautions Digital Audio Jack Coaxial FeaturesContents Disc Location of controls Remote sensor Power indicatorFront Left sideRF ANT in jack Rear sideAC Input jack JackRemote control Open the battery compartment Install two AAA batteries Power sourceTo USE AC Power Inserting BatteriesAntenna Jack Ohm Coaxial Cable Ohm Matching Transformer Antenna connectionsAntenna UHF 300 ohm CombinerCable TV connections Memorizing channels Setting the on-screen languageAir/Cable selection Automatic searchAdding Channel TV operationAdd/Delete channel Clear AllTo select the video input source Labeling channelsTo create channel labels VHF/UHF/CABLE ChannelsTo clear a Ch Label Labeling video inputsTo set the V-Chip Number buttons 0-9 , then press EnterDownloading the additional V-Chip rating system To change the passwordCC advanced Closed CaptionPicture control adjustment Adjusting the picture preferenceSelecting the color temperature Film Mode Setting the picture sizeSelecting Stereo/Second Audio Program SAP Turning off the built-in Adjusting the backSpeakers Selecting the audioResetting your settings Setting the Auto Shut OffPreparation Status display of discSpecial playback Playback procedureApple-HFS-System cannot be played MP3/WMA/JPEG and Audio CD playbackLimitations on MP3/WMA/JPEG CD playback Limitations on displayProgram playback CD Setting the Jpeg intervalSelect Files Zooming CancelRepeat playback CD Marking desired scenes Repeat playbackChanging soundtrack language Changing angles SubtitlesTitle selection DVD menuSetting the aspect ratio of TV screen Setting the languageSetting on screen display Setting the picture modePassword and setting Night ModeDigital Out Parental controlOr Enter Press or to select Password, then press or Enter Setting the new passwordEnter Password Temporary disabling of rating level by DVD discLanguage code list To connect the LCD TV/DVD to a VCR Connections to other equipmentTo connect the LCD TV/DVD to a VCR with an S-Video cord To connect to a DVD player with Component Video InputTo connect a Hdmi or a DVI device to the unit Using an AV Amplifier with built-in digital surroundTo Hdmi 1/DVI in Hdmi to DVI adapter cable Not supplied To PC/DVI AudioTo connect an audio system To return to normal mode Press Input Select againTo connect the TV/DVD to a camcorder, or a TV Game To connect the TV/DVD to a PC Personal ComputerIgnition Reception disturbancesSymptoms Problems and troubleshootingTV Broadcast Reception ChannelsDVD Remote ControlAccessories SpecificationsModel GeneralWhat your warranty does not cover How to get serviceWhat we will do How State Law relates to this warranty Product Registration Limitation of WarrantyTTE Technology, Inc West 103rd Street Indianapolis,
Related manuals
Manual 2 pages 58.67 Kb
Top Page Image Contents