RCA L32HD32D To connect an audio system, To connect the TV/DVD to a camcorder, or a TV Game

Page 38

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Connections to other equipment

 

 

 

(continued)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

To connect an audio system

This connection allows you to use an audio amplifier and external speakers, and adjust the audio level using the TV’s remote control.

To control the audio, turn on the unit and the stereo amplifier, and turn off the unit’s built-in speakers (see “Turning off the built-in speakers” on page 24).

Rear of the unit

Amplifier

To Audio (L) Input To Audio (R) Input

Audio cord (not supplied)

NOTE:

•To hear sound when using an external audio amplifier, the volume of both the unit and the amplifier must be set above 0 (zero).

For example, if the volume of the unit is set to 0, you will not be able to hear any sound, even if the volume of the amplifier is at its highest level.

To connect the TV/DVD to a camcorder, or a TV Game

To playback from a camcorder, connect the camcorder to the unit as shown.

This unit can also be used as a display device for many video games. However, due to the wide variety of signals generated by these devices and subsequent hook-up variations required, they have not all been included in the suggested connection diagrams.You’ll need to consult each component’s Owner’s Manual for additional information.

Rear of the unit

To LINE 1 or LINE 2 VIDEO/AUDIO IN

To Audio/Video OUT

Audio/Video cord

(not supplied)

or

To connect the TV/DVD to a PC (Personal Computer)

Before you connect this TV/DVD to your PC, change the adjustment of your PC’s Resolution and Refresh rate (60 Hz).

Connect one end of a (male to male) VGA cable to the video card of the computer and the other end to the VGA connector PC MONITOR on the rear of the TV/DVD. Attach the connectors firmly with the screws on the plug. In case of a Multimedia computer, connect the audio cord to the audio output of your Multimedia computer and to the AUDIO connector of the PC/DVI AUDIO IN jack of the TV/DVD.

Press INPUT SELECT on the remote control to select PC mode.

Switch on the computer. The TV/DVD can operate as the computer monitor.

Rear of the unit

To PC IN

PC/DVI

 

AUDIO IN

VGA cable (not supplied)

jack

 

 

Audio cord (not supplied)

Monitor Display modes

MODE Resolution Refresh rate

VGA 640x480 60Hz

VGA 720x400 70Hz

SVGA 800x600 60Hz

XGA 1024x768 60Hz

WXGA 1280x768 60Hz

WXGA 1280x720 60Hz

WXGA 1360x768 60Hz

To return to normal mode Press INPUT SELECT again.

NOTE:

•The on-screen displays will have a different appearance in PC mode than in TV mode.

•If there is no video signal from the PC when the unit is in PC mode, “No signal” will appear on the TV-screen.

38

51F0101A_eng.indd 38

3/10/08 10:56:12 AM

Page 37 Page 39
Image 38
Page 37 Page 39
Contents L26HD32D L32HD32D Digital Television Transition NoticeQualified Service Personnel Location of the required MarkingImportant Safety Instructions S3126AHOW to Handle the LCD Panel CondensationSafety Precautions Features Digital Audio Jack CoaxialContents Disc Front Remote sensor Power indicatorLocation of controls Left sideAC Input jack Rear sideRF ANT in jack JackRemote control To USE AC Power Power sourceOpen the battery compartment Install two AAA batteries Inserting BatteriesAntenna Antenna connectionsAntenna Jack Ohm Coaxial Cable Ohm Matching Transformer UHF 300 ohm CombinerCable TV connections Air/Cable selection Setting the on-screen languageMemorizing channels Automatic searchAdd/Delete channel TV operationAdding Channel Clear AllTo create channel labels Labeling channelsTo select the video input source VHF/UHF/CABLE ChannelsTo set the V-Chip Labeling video inputsTo clear a Ch Label Number buttons 0-9 , then press EnterTo change the password Downloading the additional V-Chip rating systemClosed Caption CC advancedSelecting the color temperature Adjusting the picture preferencePicture control adjustment Setting the picture size Film ModeSelecting Stereo/Second Audio Program SAP Speakers Adjusting the backTurning off the built-in Selecting the audioPreparation Setting the Auto Shut OffResetting your settings Status display of discPlayback procedure Special playbackLimitations on MP3/WMA/JPEG CD playback MP3/WMA/JPEG and Audio CD playbackApple-HFS-System cannot be played Limitations on displaySelect Files Setting the Jpeg intervalProgram playback CD Repeat playback CD CancelZooming Changing soundtrack language Repeat playbackMarking desired scenes Title selection SubtitlesChanging angles DVD menuSetting on screen display Setting the languageSetting the aspect ratio of TV screen Setting the picture modeDigital Out Night ModePassword and setting Parental controlEnter Password Setting the new passwordOr Enter Press or to select Password, then press or Enter Temporary disabling of rating level by DVD discLanguage code list To connect the LCD TV/DVD to a VCR with an S-Video cord Connections to other equipmentTo connect the LCD TV/DVD to a VCR To connect to a DVD player with Component Video InputTo Hdmi 1/DVI in Hdmi to DVI adapter cable Using an AV Amplifier with built-in digital surroundTo connect a Hdmi or a DVI device to the unit Not supplied To PC/DVI AudioTo connect the TV/DVD to a camcorder, or a TV Game To return to normal mode Press Input Select againTo connect an audio system To connect the TV/DVD to a PC Personal ComputerReception disturbances IgnitionTV Broadcast Reception Problems and troubleshootingSymptoms ChannelsRemote Control DVDModel SpecificationsAccessories GeneralWhat we will do How to get serviceWhat your warranty does not cover TTE Technology, Inc Product Registration Limitation of WarrantyHow State Law relates to this warranty West 103rd Street Indianapolis,
Related manuals
Manual 2 pages 58.67 Kb
Top Page Image Contents