RCA VPT 385 owner manual Programming the Timer, Following, You can program the timer to do

Page 26

Programming the Timer

The programmable clock/timer permits unattended recording of up to four different TV programs. The timer is actually a small computer which will turn on the VCR at the time you select, record for a selected length

of time, and then turn off the VCR... all automatically without you being there.

You can program the timer to do the

following:

Record a program on a single day up to one year away. [NORMAL PROGRAM]

Record a program at the same time Monday through Friday. [DAILY PROGRAM]

Record a program on one certain day of every week. [WEEKLY PROGRAM]

Things to know before you start:

You can program the timer up to one year before the TV program is to be recorded.

You can correct an error in the program any time before the last step by pressing CLEAR repeatedly until the digit to be corrected is flashing. Then

enter the correct digit and continue the programming sequence.

[

I11 Make sure the VCR's clock is set to the correct time. The timer cannot record at the right time if the clock is set incorrectly. Reset the clock if necessary.

Press PROGRAM on the remote hand unit.

The programming "menu" appears on the status display.

121 The display will prompt you to select a Program Number.

Four program numbers are available and you can enter different programming instructions in each

one. All four program numbers will be flashing because none of them have been used. If the timer

has been programmed, the number that was used will stay on instead of flashing. You must clear a program number before the same number can be used again. See "Clearing a Timer Program" on the next page.

[

131 The display will prompt you to select a channel number.

CH

]NORM

Press two digits for the channel to be recorded. (for example, press 0 4 for channel 4).

!

Simplified Programming Instructions

1.Press PROGRAM on remote hand unit.

PR_IAId

2.Watch the status display.it wilt prompt you through the rest of the programming steps.

3.Turn off the VCR

I-qCLK[] .ORM[]o_ []_..[] .Ev

Press "2" to enter a Normal Program, "3" to enter a Daily Program, or "4" to enter a Weekly Program.

[] [] NORM[] []

Press a digit from 1 to 4 on the remote to select the program number you want to program.

Program numbers can be selected in any order.

The display will prompt you to enter the recording start time.

ON

AM

.MCH Lf

]NORM

Press four digits, two for the hour and two more for the minute. For example, press 0 6 0 0 for 6:00 (Always press "'0" before a single-digit hour or minute. The "0" will not appear in the display.)

24

Image 26
Contents VideoCassette Recorder Safety Precautions Wai, ranty RegistrationUsing This Manual ContentsLocation InstallationWhen you unpack your new VCR, be sure you have Antenna Connections Disconnect Existing Antenna from TV and Connect it to VCRAntenna Connections Connect VCR to back of TVCable- TV Connections Your CABLE-TVCable Connections Operating Instructions TV Monitor/Receiver ConnectionsDirect Video and Audio Connections What Your VCR Will Do Cassette Playing Times and Speeds Video CassettesErase Protection Recording SpeedBasic Operation Basic Operating Controls and DispLaysTuner Turning on Your VCR for the First TimeProgramming Active Channels into VCRs Deleting Channels from the Scan ListSimplified Installation Checklist Setting the VCR/TV SwitchSetting Your IV to the VCR Channel Remote Control Know before you set the clock Setting the ClockHere are some things you should First Recording and Playback Operating Controls Detailed Descriptions Frame Advance Special Effects and FeaturesPause for Slop-Action Playback Tracking Control Special Effects and FeaturesSame VCR, streaks may appear in the picture. Adjust Memory StopNormal TV Viewing Quick Reference GuidesRecording Viewing Same Program Recording With TV OffRecording and Viewing Different Programs Basic Pla backRecording From Simplified Operating Instructions to Dub TapesCamera Recording Express Recording Following Programming the TimerYou can program the timer to do Things to know before you startClearing a Timer Program Programming the TimerChecking the Timer Programs AM or PMTV Viewing During a Timer Recording Timer RecordingXPR and Timer Stopping a Timer Recording in ProgressAlternate Remote Control Units IICJllCleaning Controls Inserting IndicatorFeatures Special ButtonSpecifications