Reference
Trouble Shooting Guide
Sometimes problems can be easily solved by checking a few basic things. Check below before you call for help or take your VCR to an Authorized ProScan VCR Servicenter.
|
| Trouble | Here's what to try: | ||
|
|
|
|
|
|
| No power | ■ Plug VCR into an operating outlet. | |||
|
|
| ■ Check connections. | ||
|
|
|
|
|
|
| Clock shows incorrect time or date | ■ Clock was not set accurately (check AM/PM and date). | |||
|
|
| ■ Time counter display appears in display panel. Press DISPLAY on | ||
|
|
| remote. | ||
|
|
|
|
| |
| VCR does not respond to remote | ■ Press VCR1 (VCR2¥DVD) to set remote to control the VCR. See | |||
|
|
| page 21. | ||
|
|
| ■ VCR2¥DVD button may be set to control a DVD. See page 21 to | ||
|
|
| change back to VCR2. | ||
|
|
| ■ Aim remote at VCR with no objects between them. | ||
|
|
| ■ Remove batteries and hold down one or more buttons for several | ||
|
|
| seconds to drain the microprocessor inside the remote to reset it. | ||
|
|
| Reinstall the batteries and try remote again. | ||
|
|
| ■ Change batteries. | ||
|
|
|
|
| |
| Remote no longer controls a ProScan TV | ■ Press TV to set remote to control the corresponding compatible TV. | |||
|
|
| See page 22. | ||
|
|
| ■ Reprogram remote for ProScan or RCA TV. See page 22. | ||
|
|
| ■ Aim remote at TV with no objects between them. | ||
|
|
| ■ Change batteries. | ||
|
|
| ■ Remove batteries and hold down one or more buttons for several | ||
|
|
| seconds to drain the microprocessor inside the remote to reset it. | ||
|
|
| Reinstall the batteries and try remote again. | ||
|
|
|
|
|
|
| Remote no longer controls a compatible TV, | ■ Press TV, AUX, VCR2¥DVD or SAT¥CABLE to set remote to control a | |||
| cable box, satellite receiver, or auxiliary | compatible component. See pages | |||
| component | ■ Aim remote at component with no objects between them. | |||
|
|
| ■ Reprogram remote after batteries have been changed. | ||
|
|
| ■ Reprogram VCR2¥DVD button to operate compatible satellite | ||
|
|
| receiver. See page 23. | ||
|
|
| ■ Change batteries. | ||
|
|
| ■ Remove batteries and hold down one or more buttons for several | ||
|
|
| seconds to drain the microprocessor inside the remote to reset it. | ||
|
|
| Reinstall the batteries and try remote again. | ||
|
|
|
| ||
| VCR only responds to VCR2¥DVD button on | ■ Check setting of Remote Control: VCR1/VCR2 feature. See page 21. | |||
| remote |
|
|
| |
|
|
|
|
|
|
| No picture when VCR turned on Ð using a | ■ Press TV¥VCR to turn VCR indicator on. See page 17. | |||
| basic hookup | ■ Check to see if Auto TV/VCR feature is set to OFF. See page 17. | |||
|
|
|
|
| |
| Poor or no picture for normal TV viewing | ■ Press TV¥VCR to turn VCR indicator off. | |||
|
|
| ■ Switch TV to an active channel. | ||
|
|
| ■ Check antenna connections. | ||
|
|
|
|
| |
| Time counter not working | ■ The time counter does not advance during unrecorded portions of | |||
|
|
| tape. When an unrecorded segment of tape is encountered, the time | ||
|
|
| counter will hold its count until recorded material is detected again. | ||
|
|
| ■ A minus (Ð) will appear in front of the time if you rewind the tape | ||
|
|
| farther back than a counter reading of 0:00:00. | ||
|
|
|
|
|
|
52