RCA PHD42600 manual Installation of the Monitor, Installation using a stand or wall mount bracket

Page 6

Connections and Setup

Installation of the Monitor

Installation using a stand or wall mount bracket

•Please be sure to request installation or mounting of this unit or the installation bracket by the dealer where purchased.

•When installing, be sure to use the bolts provided with the stand or installation bracket.

•For details concerning installation, please refer to the instruction manual provided with the stand or installation bracket.

Installation using accessories other than the stand or installation bracket (sold separately)

•When possible, please install using parts and accessories manufactured by Thomson. Thomson will not be held responsible for accident or damage caused by the use of parts and accessories manufactured by other companies.

•For custom installation, please consult the dealer where the unit was purchased.

Note for U.S. customers: If you prefer, we can provide you with the name of an Authorized Service Representative who will visit your home for a fee to install your electronic entertainment system and to instruct you in its operation. For details about this service, call 1-888-206-3359.

For additional assistance while using your RCA product, please visit www.rca.com/customersupport.

CAUTIONS

To avoid malfunction, overheating of this unit, and possible fire hazard, make sure that the vents on the main unit are not blocked when installing. Also, as hot air is expelled from the air vents, be careful of dust build up on rear surface wall, etc.

This monitor unit is very heavy and has little front-to-back depth, making it very unstable when stood on edge. The monitor should either be attached to the table stand or mounted on the wall. No other mounting method is recommended. As a result, two or more persons should cooperate when unpacking, moving, or installing the monitor.

This unit incorporates a thin design. To ensure safety if vibrated or shaken, please be sure to take measures to prevent the unit from tipping over.

Mounting or Removing the

Table Stand

To mount the monitor to the stand:

1. Lift the plasma monitor and insert the 4 mounting posts on the back of the unit into the mounting holes on the table stand.

2. Make sure all the posts are fully inserted, then let the monitor slide down into the smaller notches until the posts fit firmly into place.

3. Insert the screws into the holes on the back of the stand (as shown) and tighten them into place.

To remove the monitor from the stand:

Remove the screws, and follow the above steps in reverse order.

Stand holes for the monitor’s mounting posts

4

Graphics contained within this publication are for representation only.

Chapter 1

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Plasma Monitor User’s Guide Changing Entertainment. AgainImportant Information Product RegistrationProduct Information Table of Contents Other Information Connections and Setup Things to Consider Before You ConnectMounting or Removing Table Stand Installation of the MonitorInstallation using a stand or wall mount bracket To mount the monitor to the standFront of Your Monitor Explanation of Jacks Back Panel VID1 and VID2Speakers Using the VID1 and VID2 jacks Choose Your ConnectionConnection to audio/video components Using the Component Video jacks Y, Pb, Pr Using the DVI in jackUsing the Audio OUT jacks Using the RGB in jackConnection to a personal computer Connecting speakers Connection to an external monitorPut batteries in the remote Set up Your MonitorPlug in the Monitor Turn on the MonitorUsing the Remote Control Button Descriptions for Monitor ModeVOL and buttons Adjust the volume Button Descriptions for Other Components Programming the Remote to Operate Other Components Using the Input ButtonUsing Automatic Code Search Find Out If You Need to Program the RemoteHow to Use the Remote After You’ve Programmed It Using Direct EntryRemote Control Codes VCRDVD How to Set Up the Autotuning Feature Using the Monitor’s FeaturesWhy You Should Use the Autotuning Feature About the Status DisplayZoom Modes Arrow buttons Remote Control Buttons for Zoom ModesAuto Set OK/ZOOM buttonExiting a menu Using the Menu SystemMenus, On-screen Help and Control Panels ControlsPicture Menu Choice FieldsPicture Menu when using DVI or RGB inputs Picture GeometryAdvanced Settings Sound Menu Preferences MenuTroubleshooting Other InformationCare and Cleaning Sound okay, picture poorSpecifications RGB/DVI Package Dimensions Maximum ResolutionDimensions Without Stand With Stand WeightAcoustics Power Management Mode Sync Video Power dissipationNon-Operating SoundIndustry Canada Compliance Notice Limited Warranty Product Registration Limitation of Warranty How State Law relates to warrantyIf you purchased your unit outside the United States Standard Audio/Video Accessory InformationHow to Order Component VideoATSC21 Hdtv set-top box receives PLWM42J2 Plasma monitor wallThomson
Top Page Image Contents