Serviceman mode
CAT (computer aided test) Mode
CAT mode menu |
|
|
|
|
|
|
|
| ||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||
|
|
|
|
| CAT Panel |
|
|
|
|
|
|
|
| |||||||||
|
|
|
|
|
|
| Mode |
| Function | Access Button | ||||||||||||
|
|
|
|
|
| sys8.1 |
|
|
| |||||||||||||
|
|
|
|
|
|
|
| IIC |
| Service Alignment | Action | |||||||||||
|
|
|
|
|
| IIC Mode |
|
|
| |||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
| CD Mode |
|
| CD |
| Software Version | Mute | ||||||||||
|
|
|
|
|
|
|
| (Complete | Information EEPROM | More than 5 | ||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Diagnostics) | Edit | seconds | ||||
|
|
|
|
|
| SD Mode |
|
| SD (Status | MTBF Parameter | Action | |||||||||||
|
|
|
|
|
|
|
| Display) |
|
| ||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
| MS Mode |
|
| MS Mode | Not used | ||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||
|
|
|
|
|
| ID Mode |
|
| ID |
| Not used | |||||||||||
Remote Control | Status |
|
|
| How to access the CAT mode. | |||||||||||||||||
|
|
| ||||||||||||||||||||
|
|
|
|
|
| VOL |
|
|
| |||||||||||||
|
|
|
|
|
|
|
|
| ||||||||||||||
|
|
|
|
|
|
| Press and hold the Volume/Down button on the | |||||||||||||||
|
|
|
|
|
|
| ||||||||||||||||
|
|
|
|
|
| VOL Up/Dow n | ||||||||||||||||
|
|
|
|
|
| |||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||
|
|
|
|
|
|
|
|
|
|
| R | Return |
|
|
| front panel of the unit and press the status | ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| button on the remote control three times within | |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| VOL Up/Dow n |
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| one second, this will place the unit into the CAT | |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| Left/Right |
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Mode. |
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
| Action |
|
|
| To exit the CAT mode, access the ID mode and | ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
switch off the main power. | ||||||||||||||||||||||
|
|
|
I2C Mode
Select the I2C mode by pressing the Up/Down button on the remote control from the front page of the CAT menu, and then press the Action button on the remote control.
How to use the I2C mode?
1.Select the alignment subject by pressing the UP/Down buttons on the remote control.
2.Select the alignment item by pressing the Left and Right buttons on the remote control.
3.Adjust the optimum setting by pressing the Volume Up/Down buttons on the remote control.
4.The data is memorized when the R button is pressed on the remote control or the alignment Subject (or item) is changed.
To exit the I2C mode, press the R button on the remote control.
81