Panasonic TH50PHW5 Hidden Option Menu for GPH5D series, Option menus Default setting Contents

Page 55

Settings the Action Menu

1.Use the Up/Down buttons to select the desired item.

2.Use the Left / Right Buttons to select the desired function

Figure 59

The option menu will disappear 60 seconds after the operation.

Press the R button to exit the Option Menu.

Figure 60

Hidden Option Menu for GPH5D series

GPH5D chassis series have special function and operation setting facility that is called “Option Menu”. This Option Menu is useful for special functions that are required by certain customers. This should be set at the installation stage. The end user could not set or change these because the optional On Screen menu is hidden and accessible via the CAT-mode only.

Option menus

Default setting

Contents

Wobbling

Off

Wobbling operation On/Off.

 

 

The outline of burnt image will be blurred by

 

 

intermittent image shift.

Off-timer function

Enable

Off-timer operation Enable/Disable.

On Screen display

Off

Enable/Disable to display input mode

 

 

indication after power on and no signal

 

 

indication.

Input Initial

Off

Sets the initial input mode when the power is

 

 

turned on. Allow input mode selection while

 

 

power is on.

Initial VOL. level

 

Sets the initial volume level when the power is

 

 

turned on. Allow Volume control while power

 

 

is on.

Maximum VOL. Level

Off

Sets the maximum volume to desired level.

 

 

Volume cannot exceed this level.

INPUT lock

Off

Fixes the input mode to AV, Component/RGB

 

 

or PC. Cannot change input mode by input

 

 

selection key.

Button lock

Off

Enable/Disable front operation buttons (Input

 

 

and/or volume up/down)

Studio W/B

Off

Set warm mode color temperature to 3,200

 

 

Kelvin.

Remote control User

Off

Remote key invalidation

Level

 

Off: All keys of the remote are valid.

 

 

User1: The keys that are Valid are: Stand-by

 

 

(ON/OFF), Input, Status, Surround, Sound

 

 

mute On/Off, and volume adjustment.

 

 

User2: The key that is Valid is only the Stand-

 

 

by (ON/OFF).

56

Image 55
Contents Troubleshooting Guide Panasonic Services Company National TrainingPage Page Objective HD Plasma Display HD Panel Digital Cinema Reality Model Line UpInterlace SpecificationsPanasonic Company PI Company F/H Scanning MethodHD High-Definition panel FeaturesProtection New frontModel Differences Single Scan SD Rear Cover Removal DisassemblyPage Printed Circuit Board Information Table HD PCB Board Layout DiagramTXNP110MHS PCB Board Layout DiagramSD PCB Layout Diagram HY/HZ Board Video Signal Path ExplanationHX Board D1 Board DVI Interface Page Composite/ Component Video Input mode Sync RGB/PC Input Mode SyncSync Process IC9007 A/D Converter IC3001 Video SwitchD1 Board D1 Main ICs OperationD2 Board D2 Board details SC Board Explanation Page Page SS Board Explanation Page Page Standby Power Supply Power SuppliesPower Factor Control Main Power SupplyVoltage Regulation Low Voltage Power supplyHigh Voltage Power Supply Page Protection Circuits Page Self Check Display Indication Diagnostic ProceduresPower LED Flashing timing chart No Power Diagnostic Flow ChartsPower LED is red and blinking on/off Power LED blinks twice No Picture Flowchart Are the video signals Dark picture Flowchart Local screen failure Service HintsPage Page Page Page Page Panasonic After Image Prevention Screen Saver FeatureSide Bar Brightness adjustment Accessing the Option Menu Option SettingHidden Option Menu for GPH5D series Option menus Default setting ContentsPage Sample Waveforms CN H2, Pin A8 CN H2, Pin A19 5ms /div 1ms/ div Page HX board Page SC Board Input Signals SC Board Waveforms CLK SS-Board Input Signals SS Board Waveforms Check Zone PDP Defect Pixel SpecificationBoard Connectors Connector TablesBoard Connectors OUT Board Connectors HX- Board Connectors HY / HZ- Board Connectors Panel label Information Adjustment Procedures∙ Adjustments Adjustment table+B Set-up Driver Set-up AdjustmentsItem / Preparation Initialization Pulse Adjust Adjustment Volume Locations B. Printed Circuit Board exchange procedureQuick adjustment after P.C.B. exchange Test Point locations I2C Mode Serviceman modeCAT computer aided test Mode How to access the CAT modeMemory data change CD modeOSD SD ModeI2C Menu Structure Ntsc Panel White Balance Alignment ProceduresPedestal Setting PC/RGB Panel White Balance Page HD /525i /525P Panel White Balance Page 625i Panel White Balance Sub Brightness Setting
Related manuals
Manual 91 pages 8.91 Kb