Digital output

Delay time (b)

[DVD-V](Dolby Digital, center and surround speakers only)

For optimum listening with 5.1-channel sound, all the speakers, except for the subwoofer, should be the same distance from the seating posi- tion. If you have to place the center or surround speakers closer to the seating position, adjust the delay time to make up for the difference.

If distance d (from the center speaker) and f (from the surround speakers) are the same as or greater than e (from the front speak- ers), leave the delay time as “0”, the factory preset.

If either distance d or f is less than e, find the difference in the relevant table and change to the recommended setting.

LS RS

Changing the delay time

1.Press [3, 4, 2, 1] to select the delay time box and press [ENTER].

2.Press [3, 4] to adjust the delay time and press [ENTER].

≥Center speaker

Difference	Setting

Approx. 50 cm (11/2 feet)	1.3 ms
Approx. 100 cm (3 feet)	2.6 ms

Approx. 150 cm (5 feet)	3.9 ms

Approx. 200 cm (6 feet)	5.3 ms

≥Surround speakers

Difference	Setting

Approx. 200 cm (6 feet)	5.3 ms

Approx. 400 cm (12 feet)	10.6 ms

Approx. 600 cm (18 feet)	15.9 ms

Channel balance (c)

1.Press [3, 4, 2, 1] to select “Test” and press [ENTER].

A test signal is output from one speaker at a time, starting with the front left speaker and proceeding clockwise.

FRONT(L)_--)CENTER_--)FRONT(R)

:; SURROUND(L)(-----------==SURROUND(R)

2.While listening to the test signal, press [3, 4] to adjust the volume of the center and surround speakers so they are the same apparent volume as the front speakers.

(The front speakers cannot be adjusted here.)

3.Press [ENTER]. The test signal stops.

Note

No signal is output for the subwoofer. To adjust its volume, play something, then return to this screen to adjust to suit your taste.

When you are finished

Press [3, 4, 2, 1] to select “Exit” and press [ENTER].

Note

The unit may be unable to output as set here due to limitations im- posed by the unit itself or the disc being played. (The display’s “P.PCM” indicator lights or “D.MIX” indicator goes out in these cases.)

[DVD-A] [DVD-V]

Change the settings when you have connected equipment through this unit’s DIGITAL AUDIO OUT terminal (OPTICAL).

PCM Down Conversion

Select how to output the high-quality audio signals (sampling fre- quencies of 96 kHz and 88.2 kHz) on discs that do not have copy- right protection. Choose the settings to suit the equipment you have connected.

Equipment
(Able to handle	Setting	Audio output
88.2 kHz or more)

Yes	No	Output as is
Yes	No	Output as is

No	Yes	Down-sampled to
No	Yes	Down-sampled to	operations
		48 kHz or 44.1 kHz	operations
		48 kHz or 44.1 kHz

The equipment cannot output signals of 88.2 kHz or more if the set-
ting is “No” and the equipment is unable to handle these signals.
≥Signals are down-sampled to either 48 kHz or 44.1 kHz despite the			Advanced
Note

≥Some equipment cannot handle sampling frequencies of 88.2 kHz, even if they can handle 96 kHz. Read your equipment’s operating instructions for details.

above settings if they have a sampling frequency of 176.4 kHz or more or are copyright protected.

Dolby Digital

Bitstream (Factory preset):

When you have connected a unit with a built-in Dolby Digital decoder.

PCM:

When you have connected a unit that doesn’t have a built-in Dolby Digital decoder.¢

DTS Digital Surround

PCM (Factory preset):

When you have connected a unit that doesn’t have a built-in DTS decoder.¢

Bitstream:

When you have connected a unit with a built-in DTS decoder.

¢These changes to digital audio output must be made, otherwise bitstream signals the decoder cannot handle will be output. If these signals are output, “noise” will be output which can cause harm to your ears and speakers.

RQT6270