Panasonic TH-103PF10UK manual Normalization, This functions when display is turned on

Page 47

Options Adjustments

 

Options

3/3

 

 

Slot power

Off

 

Power On Screen Delay

Off

 

V. lnstallation

Off

 

Rotate

Off

 

Serial Slot Select

Slot1

 

Item

Effect

 

 

 

Adjustments

 

 

 

Off

 

Auto

On

 

 

 

 

Off:

Power is not transmitted to the slot power.

 

 

Slot Power

Auto: Power is transmitted to the slot power only when main power is on.

 

On:

Power is transmitted to the slot power when main power is on or in the standby state.

 

 

 

 

Note: In some cases, power is transmitted to the slot power when main power is on or in the standby

 

 

state regardless of the slot power setting.

 

 

 

 

 

 

 

 

 

 

 

Off

1

2

3....

30

 

 

 

You can set the power-on delay time of the displays to reduce the power load, when you press

to

 

turn on the multiple displays that are set together, for example, on MULTI DISPLAY system.

 

 

Set each display’s setting individually.

 

 

 

Off:

 

The display will be turned on at the same time as

is pressed.

 

 

1 to 30 (sec.): Set the power-on delay time (second).

 

 

Power On

Notes:

 

After pressing

, the display will be powered on with time delay depending on this setting.

 

 

 

 

 

 

Screen Delay

• During this function is working, the power indicator is blinking green.

 

•This function also works when the power recovers from failure or after plugging off and in again the power cord.

After you unplug and plug the power cord in while the unit is in standby mode and also the power is being supplied to a terminal board, the unit will start supplying the power to the board with time delay according to the setting.

The power indicator lights up red first and it turns orange when the power starts being supplied to the board.

 

 

 

Off:

Sets fan to the horizontal installation mode.

V.Installation

 

 

On:

Sets fan to the vertical installation mode.

Off

On

Notes:

 

 

 

• This functions when display is turned on.

 

 

 

 

 

 

• If the display is installed vertically, the power switch should be located at the bottom.

 

 

 

 

 

Rotate

 

 

Off:

Does not rotate the image.

Off

On On:

Rotates the image 180 degrees.

 

Serial Slot

 

 

Slot1

Slot2

Slot3

 

 

Selects the slot which communicates serial.

Select

 

 

 

 

Note: The setting of an external command can be set only from the fixed serial terminal. (see page 11)

 

 

 

Normalization

When both main unit buttons and remote control are disabled due to the “Button lock”, “Remocon User level” or “Remote ID” adjustments, set all the values “Off” so that all the buttons are enabled again.

Press the

- /button on main unit together with

button on the remote control and hold for more than 5 seconds. The

“SHIPPING” menu is displayed and the lock is released when it disappears.

47

Page 46 Page 48
Image 47
Page 46 Page 48
Contents English High Definition Plasma DisplayOperating Instructions Model No. TH-103PF10UKRisk of Electric Shock Do not Open Important Safety Instructions Table of Contents Trademark Credits FCC CautionCanadian Notice When using the Plasma Display Safety PrecautionsAC Power Supply Cord MaintenanceSafety Precautions / Maintenance SetupRemote Control Batteries AccessoriesAccessories Supplied Open ConnectionsAudio OUT Terminals connection CloseConnections Signal Names for Mini D-sub 15P ConnectorPC Input Terminals connection Basic format for control data CommandSerial Terminals connection Communication parametersDTV-STB Hdmi connectionComponent / RGB connection DVDRight side surface Power on / OFFConnecting the AC cord plug to the Plasma Display Connecting the plug to the Wall OutletBasic Controls Basic Controls Advanced Picture SetupSettings On-Screen Menu DisplaysComponent Power on Time Power OFF TimeOn-Screen Menu Displays INPUT1 INPUT2A INPUT2B INPUT3 PC Selecting the input signalInitial selections Selecting the On-Screen Menu LanguagePicture Explanation During Multi PIP OperationsNormal Full During COMPONENT, RGB and PC input signal Adjusting POS. /SIZESize / DOT Clock / Clock Phase / 11 Pixel Mode Press to adjust POS. /SIZEAdjusting POS. /SIZE Multi PIP Longer than 5 seconds. Press to change input signalPress to confirm Off Sets normal two screen display modeOn Sets Advanced PIP mode Advanced PIPCinema Picture AdjustmentsStandard DynamicPicture Adjustments Advanced SettingsTreble Sound AdjustmentBass MIDMute Sound AdjustmentSDI Sound Output SurroundSelect the magnification required for the enlarged display Digital ZoomDisplay the operation guide Select the area of the image to be enlargedButton Forward Present Time SetupPresent Time Setup Press to set up DAY or Present Time of DAYPower on Time / Power OFF Time SET UP TimerDisplay the SET UP Timer Screen Press to select Negative / Scroll selection Mode selectionStart setting Screensaver For preventing image retentionScreensaver For preventing image retention Setup of Screensaver TimeReduces screen image retention Press to exit from Screensaver Side BAR AdjustOFF Dark MID Bright Addition sign Selected Input Reduces power consumptionCustomizing the Input labels Portrait Setup will be unavailable SET UP for Multi DisplayHow to setup Multi Display If you set Multi Display Setup to onDisplay Number locations for each arrangement Examples SET UP for Multi DisplayPress to select Seam Hides Video Press to select OFF, on AI-Control ID Remote Control FunctionID remote control button operation ID CancellationPress to select Seam Hides Video SET UP for PortraitHow to setup Portrait Undisplayed area 48 dots Set a mode of image division for Portrait functionLocation Viewing Area LocationComponent RGB SET UP for Input SignalsComponent / RGB in Select 3D Y/C Filter For Ntsc AV imagesRefresh Rate SET UP for Input SignalsPress Action button Press to exit from adjust mode Video NR / Block NR / Mosquito NRColor System Color System / Panasonic AutoPulldown Displays the H Horizontal / V Vertical frequencies Setting RGB sync signalSync FREQ. kHz / V-FREQ. HzOptions Adjustments Options Adjustments Sets the color temperature for TV studio When Disable is set, the Off-timer is cancelledEnable ID remote control functions Off Nullify all the settings adjusted Studio W/BRotates the image 180 degrees This functions when display is turned onNormalization Rotate Off Does not rotate the imageWeekly Command Timer Press to set each item Press to select a command numberPress to select Time / Command Time Set the time to execute a command programShipping condition Plasma Display panel TroubleshootingSymptoms Checks Symptoms CheckCOMPONENT/RGB/PC/VIDEO input signals VGA60 COMPONENT/RGB/PC/VIDEO input signalsVideo input Hdmi MHz Active pixels Pixels Active lines LinesCommand list of Weekly Command Timer Specifications Limits and Exclusions Panasonic Canada Inc Limited Warranty StatementMemo Memo Panasonic Canada Inc Customer’s RecordPanasonic Professional Display Company Executive Office
Top Page Image Contents