Panasonic TH 50PHD3 How to connect the PC Input Terminals, Signal Names for D-sub 15P Connector

Page 16

Connections

How to connect the PC Input Terminals

COMPUTER

Conversion adapter (if necessary)

RGB

AUDIO

PC IN

D-sub 15p

PC cable

Audio

1/8" (3mm) Stereo Plug

Connect a cable which matches

the audio output terminal on the computer.

Notes:

(1)Computer signals which can be input are those with a horizontal scanning frequency of 15.5 to 110 kHz and vertical scanning frequency of 48 to 120 Hz. (However, signals cannot be displayed if signals exceeding 1200 lines will not be displayed properly.)

(2)The display resolution is a maximum 1024 ⋅ 768 dots when the aspect mode is set to “4:3”, and 1366 ⋅ 768 dots when the aspect mode is set to “16:9”. If the display resolution exceeds these maximums, it may not be possible to show fine detail with sufficient clarity.

(3)The PC input terminals are DDC1/2B-compatible. If the computer being connected is not DDC1/2B-compatible, you will need to make setting changes to the computer at the time of connection.

(4)Some PC models cannot be connected to the set.

(5)An adapter is required to use the PC cable (D-sub 15P) to connect a Macintosh computer to the set.

(6)There is no need to use an adapter for computers with DOS/V compatible D-sub 15P terminal.

(7)The computer shown in the illustration is for example purposes only.

(8)Additional equipment and cables shown are not supplied with this set.

(9)Do not set the horizontal and vertical scanning frequencies for PC signals which are above or below the specified frequency range.

Signal Names for D-sub 15P Connector

11 12 13 14 15

6 7 8 9 10

1 2 3 4 5

Pin Layout for PC Input Terminal

Pin No. Signal Name

1R

2G

3B

4GND (Ground)

5GND (Ground)

Pin No.	Signal Name	Pin No.
6	GND (Ground)	11
7	GND (Ground)	12
8	GND (Ground)	13
9	NC (not connected)	14
10	GND (Ground)	15

Signal Name

GND (Ground)

SDA

HD/SYNC

VD

SCL

16

Image 16

Contents High Definition Plasma Display Operating InstructionsEnglish Page Page Table of Contents Important Safety Notice Setup Safety PrecautionsWhen using the High Definition Plasma Display Safety Precautions Cleaning and maintenanceIf problems occur during use Accessories Accessories SupplyOptional Accessories Check that you have the accessories and items shownRemote Control Batteries Precaution on battery useObserve the following precaution Helpful HintBasic Controls Input button AVS-Video/Component, RGB/PC Mode Selection Sound mute On/Off see Volume AdjustmentButton Access button OFF Timer buttonConnections Cable fixing bandsHow to connect the AV Input Terminals Video Signal ConnectionConnections Video 4 pin socketHow to connect the Tuner Input Terminals TunerComponent signals Y, PB, PR Connection How to connect the COMPONENT/RGB Input TerminalsRGB signal R, G, B, HD, VD Connection How to connect the PC Input Terminals Signal Names for D-sub 15P ConnectorHow to connect the Serial Terminals CommandCommunication parameters Basic format for control dataPower On/Off Power On/Off and input signal selectionConnecting the plug to the Wall Outlet Note Select the input signal Power On/Off and input signal selectionOn screen Menu Display from Remote Control To Advanced settings menu seeOn screen Menu Display from Remote Control Selecting the On-Screen Menu LanguageAspect Controls Aspect Controls Adjusting Picture Pos./Size Adjusting screenAdjusting Picture Pos./Size Size Clock Phase RGB/PC in ModeHelpful Hint N / Normalise Normalisation PosSound Adjustment MuteBass TrebleSurround Controls OffPicture Adjustments Normal NormalAdvanced settings Model TH-50PHD3 only Picture AdjustmentsComponent/RGB-in select Setup for input signals3D Y/C Filter For Ntsc video images Setup for input signals Colour system / Panasonic AutoClamp position Pull-in rangeFreq. kHz/V-Freq. Hz Troubleshooting Plasma Display panel Symptoms CheckSpecifications Specifications DimensionsWeight Mass Optional SuppliedCustomer’ Record