Panasonic TH-37PWD6UX, TH-42PWD6UX manual Accessories Supplied, Remote Control Batteries

Page 8

Accessories

Accessories Supplied

Check that you have the Accessories and items shown

Operating Instruction book

Remote Control

Transmitter

EUR646529

		INPUT
	SURROUND
	VOL
N		R
PICTURE	SOUND	SET UP
MULTI		ZOOM
PIP	SWAP SELECT	MOVE
PICTURE
POS. /SIZE		ASPECT
PC	OFF TIMER

PLASMA DISPLAY

Batteries for the Remote Control Transmitter

(AA Battery ⋅ 2)

AC cord

Ferrite core (small size) ⋅ 1

Ferrite core (large size) ⋅ 2

Fixing bands

Remote Control Batteries

Requires two AA batteries.

1.Turn the transmitter face down. Press and slide off the battery cover.

2.Install the batteries as shown in the battery compartment.

(Polarity + or – must match the markings in the compartment.)

3.Replace the cover and slide in reverse until the lock snaps.

Two "AA" size

Helpful Hint:

For frequent remote control users, replace old batteries with

Alkaline batteries for longer life.

Precaution on battery use

Incorrect installation can cause battery leakage and corrosion that will damage the remote control transmitter.

Observe the following precautions:

1.Batteries should always be replaced as a pair. Always use new batteries when replacing the old set.

2.Do not combine a used battery with a new one.

3.Do not mix battery types (example: “Zinc Carbon” with “Alkaline”).

4.Do not attempt to charge, short-circuit, disassemble, heat or burn used batteries.

5.Battery replacement is necessary when the remote control acts sporadically or stops operating the Plasma Display.

8

Image 8

Contents Operating Instructions Model No. TH-37PWD6UXProgressive Wide Plasma Display EnglishRisk of Electric Shock Do not Open Important Safety Instructions Table of Contents Trademark Credits FCC CautionAttach the ferrite core Safety Precautions Set upAC Power Supply Cord If problems occur during useCleaning and maintenance When using the Plasma DisplayTY-ST42PW1 TY-CE42PS1Remote Control Batteries AccessoriesAccessories Supplied Connections SpeakersAC cord fixing Cable fixing bandsSignal Names for D-sub 15P Connector PC Input Terminals connectionSDA HD/SYNCInstalling the ferrite core Large size Command Basic format for control dataSerial Terminals connection Communication parametersPower ON/OFF Power ON/OFFConnecting the plug to the Wall Outlet AC cord connectionSelecting the On-Screen Menu Language Input Signal SelectionSelect the Input Signal Basic Controls NormalZoom Press to access SET UP button seeOFF Timer button Stand-by ON/OFF buttonOn-Screen Menu Displays DURATION/ Saver Time / Power OFF TimeTIME/ Power OFF Time Mode Picture Explanation Aspect ControlsNormal Zoom Full NormalAdjusting Picture POSITION/SIZE Adjusting screenSIZE/CLOCK Phase RGB/PC in ModeSound Adjustment MuteNormal Cool Warm Picture AdjustmentsAuto Standard Cinema Dynamic Advanced Settings Present Time Setup SET UP TimerSET UP Timer Power on TIME/POWER OFF TimePower OFF Time Power OFF FunctionMode selection Start settingScreensaver For preventing after-images Negative / Scroll selectionPeak Limit Setup of Screensaver TimeReduces screen after-image Press to exit from Screensaver Side BAR AdjustOFF, DARK, MID, Bright OFF Dark MID Bright Digital Zoom Display the Operation GuideSelect the area of the image to be enlarged Select the magnification required for the enlarged displayReduces power consumption Customizing the Input labelsSET UP for Multi Display How to setup Multi DisplayMulti Display Setup Multi DisplayPress to select Arrangement 2nd step Press to select 2 ⋅ 2, 3 ⋅SET UP for Input Signals COMPONENT/RGB in SelectComponent RGB 3D Y/C Filter For Ntsc Video imagesColor System / Panasonic Auto PulldownColor System Auto PAL Secam NtscSetting RGB sync signal SyncFREQ. kHz/V-FREQ. Hz Displays the H Horizontal/V Vertical frequenciesTroubleshooting Plasma Display panel Symptoms CheckComponent Input signal can be displayedMark Specifications TH-37PWD6UX TH-42PWD6UXPage Panasonic Commercial Plasma Display Limited Warranty Customer’s Record