Panasonic TH-42PWD6UX, TH-37PWD6UX Connections, Speakers, AC cord fixing, Cable fixing bands

Page 9

Connections

When connecting the speakers, be sure to use only the optional accessory speakers. Refer to the speaker’s Installation Manual for details on speaker installation.

Speakers (Optional accessories)

SPEAKERS

Terminals (L)

SPEAKERS	AC cord connection (see page 12)
Terminals (R)	– AC cord fixing

1
2	1
	1
	2

1.Open the clamper.

Clamper

2.Insert the AC cord and close the clamper securely.

AC cord

3.Slide up the clamper and fix the AC cord plug securely.

When loosen the clamper:

Note: The power plug in the illustration may not be the type fitted to your set.

–Cable fixing bands

Secure any excess cables with bands as required.

Pass the attached cable fixing band through the clip as shown in the figure.

1

To secure cables connected to Terminals, wrap the cable fixing band around them then pass the pointed end through the locking block, as shown in the figure.

While ensuring there is sufficient slack in cables to minimize stress (especially in the power cord), firmly bind all cables with the supplied fixing band.

To tighten:	To loosen:
	Push the
Pull	catch
Pull
2	Pull

Optional Terminal Board insert Slots (covered)

AUDIO

PC IN

SERIAL

SLOT1

SLOT2

SLOT3

From EXTERNAL monitor terminal on Computer (see page 10)

From SERIAL Terminal on Computer (see page 11)

9

Image 9

Contents Model No. TH-37PWD6UX Operating InstructionsProgressive Wide Plasma Display EnglishRisk of Electric Shock Do not Open Important Safety Instructions Table of Contents FCC Caution Attach the ferrite coreTrademark Credits Set up Safety PrecautionsAC Power Supply Cord If problems occur during useWhen using the Plasma Display Cleaning and maintenanceTY-ST42PW1 TY-CE42PS1Accessories Accessories SuppliedRemote Control Batteries Speakers ConnectionsAC cord fixing Cable fixing bandsPC Input Terminals connection Signal Names for D-sub 15P ConnectorSDA HD/SYNCCommand Basic format for control data Installing the ferrite core Large sizeSerial Terminals connection Communication parametersPower ON/OFF Power ON/OFFConnecting the plug to the Wall Outlet AC cord connectionInput Signal Selection Select the Input SignalSelecting the On-Screen Menu Language Normal Basic ControlsSET UP button see Zoom Press to accessOFF Timer button Stand-by ON/OFF buttonOn-Screen Menu Displays Time / Power OFF Time TIME/ Power OFF TimeDURATION/ Saver Aspect Controls Mode Picture ExplanationNormal Zoom Full NormalAdjusting screen Adjusting Picture POSITION/SIZESIZE/CLOCK Phase RGB/PC in ModeMute Sound AdjustmentPicture Adjustments Auto Standard Cinema DynamicNormal Cool Warm Advanced Settings SET UP Timer Present Time SetupPower on TIME/POWER OFF Time SET UP TimerPower OFF Time Power OFF FunctionStart setting Mode selectionScreensaver For preventing after-images Negative / Scroll selectionSetup of Screensaver Time Reduces screen after-imagePeak Limit Side BAR Adjust OFF, DARK, MID, Bright OFF Dark MID BrightPress to exit from Screensaver Display the Operation Guide Digital ZoomSelect the area of the image to be enlarged Select the magnification required for the enlarged displayCustomizing the Input labels Reduces power consumptionHow to setup Multi Display SET UP for Multi DisplayMulti Display Setup Multi DisplayPress to select 2 ⋅ 2, 3 ⋅ Press to select Arrangement 2nd stepCOMPONENT/RGB in Select SET UP for Input SignalsComponent RGB 3D Y/C Filter For Ntsc Video imagesPulldown Color System / Panasonic AutoColor System Auto PAL Secam NtscSync Setting RGB sync signalFREQ. kHz/V-FREQ. Hz Displays the H Horizontal/V Vertical frequenciesPlasma Display panel Symptoms Check TroubleshootingInput signal can be displayed MarkComponent TH-37PWD6UX TH-42PWD6UX SpecificationsPage Panasonic Commercial Plasma Display Limited Warranty Customer’s Record