Panasonic TH-37PWD6UX, TH-42PWD6UX manual PC Input Terminals connection, Sda, Hd/Sync, Scl

Page 10

Connections

PC Input Terminals connection

COMPUTER

AUDIO

PC IN

	Conversion adapter		Less than	Ferrite core (large size)
	Conversion adapter		3" 15/16	Ferrite core (large size)
	(if necessary)		3" 15/16	(supplied)
			(10 cm)	D-sub 15p
				RGB
				PC cable
		Ferrite core (small size)		Less than
		Ferrite core (small size)		3" 15/16
			(supplied)	(10 cm)

Audio

Stereo plug

Connect a cable which matches

the audio output terminal on the computer.

Installing the ferrite core (Small size)

1

2

Pull back the tabs (in two places)

Installing the ferrite core (Large size)

1

2

Pull back the tabs (in two places)

3

Open

Press the cable through and close

3

Open

Press the cable through and close

Notes:

(1)Computer signals which can be input are those with a horizontal scanning frequency of 15 to 110 kHz and vertical scanning frequency of 48 to 120 Hz. (However, the image will not be displayed properly if the signals exceed 1,200 lines.)

(2)The display resolution is a maximum of 640 ⋅ 480 dots when the aspect mode is set to “4:3”, and 852 ⋅ 480 dots when the aspect mode is set to “16:9”. If the display resolution exceeds these maximums, it may not be possible to show fine detail with sufficient clarity.

(3)The PC input terminals are DDC1/2B-compatible. If the computer being connected is not DDC1/2B-compatible, you will need to make setting changes to the computer at the time of connection.

(4)Some PC models cannot be connected to the set.

(5)There is no need to use an adapter for computers with DOS/V compatible D-sub 15P terminal.

(6)The computer shown in the illustration is for example purposes only.

(7)Additional equipment and cables shown are not supplied with this set.

(8)Do not set the horizontal and vertical scanning frequencies for PC signals which are above or below the specified frequency range.

(9)Component Input is possible with the pin 1,2,3 of the D-sub 15P Connector.

Signal Names for D-sub 15P Connector

11 12 13 14 15

6 7 8 9 10

1 2 3 4 5

Pin Layout for PC Input Terminal

Pin No. Signal Name

1R (PR/CR)

2G(Y)

3B(PB/CB)

4GND (Ground)

5GND (Ground)

Pin No.	Signal Name	Pin No.	Signal Name
6	GND (Ground)	11	GND (Ground)
7	GND (Ground)	12	SDA
8	GND (Ground)	13	HD/SYNC
9	NC (not connected)	14	VD
10	GND (Ground)	15	SCL

10

Image 10

Contents Progressive Wide Plasma Display Operating InstructionsModel No. TH-37PWD6UX EnglishRisk of Electric Shock Do not Open Important Safety Instructions Table of Contents Attach the ferrite core FCC CautionTrademark Credits AC Power Supply Cord Safety PrecautionsSet up If problems occur during useTY-ST42PW1 Cleaning and maintenanceWhen using the Plasma Display TY-CE42PS1Accessories Supplied AccessoriesRemote Control Batteries AC cord fixing ConnectionsSpeakers Cable fixing bandsSDA Signal Names for D-sub 15P ConnectorPC Input Terminals connection HD/SYNCSerial Terminals connection Installing the ferrite core Large sizeCommand Basic format for control data Communication parametersConnecting the plug to the Wall Outlet Power ON/OFFPower ON/OFF AC cord connectionSelect the Input Signal Input Signal SelectionSelecting the On-Screen Menu Language Basic Controls NormalOFF Timer button Zoom Press to accessSET UP button see Stand-by ON/OFF buttonOn-Screen Menu Displays TIME/ Power OFF Time Time / Power OFF TimeDURATION/ Saver Normal Zoom Full Mode Picture ExplanationAspect Controls NormalSIZE/CLOCK Phase Adjusting Picture POSITION/SIZEAdjusting screen RGB/PC in ModeSound Adjustment MuteAuto Standard Cinema Dynamic Picture AdjustmentsNormal Cool Warm Advanced Settings Present Time Setup SET UP TimerPower OFF Time SET UP TimerPower on TIME/POWER OFF Time Power OFF FunctionScreensaver For preventing after-images Mode selectionStart setting Negative / Scroll selectionReduces screen after-image Setup of Screensaver TimePeak Limit OFF, DARK, MID, Bright OFF Dark MID Bright Side BAR AdjustPress to exit from Screensaver Select the area of the image to be enlarged Digital ZoomDisplay the Operation Guide Select the magnification required for the enlarged displayReduces power consumption Customizing the Input labelsMulti Display Setup SET UP for Multi DisplayHow to setup Multi Display Multi DisplayPress to select Arrangement 2nd step Press to select 2 ⋅ 2, 3 ⋅Component RGB SET UP for Input SignalsCOMPONENT/RGB in Select 3D Y/C Filter For Ntsc Video imagesColor System Color System / Panasonic AutoPulldown Auto PAL Secam NtscFREQ. kHz/V-FREQ. Hz Setting RGB sync signalSync Displays the H Horizontal/V Vertical frequenciesTroubleshooting Plasma Display panel Symptoms CheckMark Input signal can be displayedComponent Specifications TH-37PWD6UX TH-42PWD6UXPage Panasonic Commercial Plasma Display Limited Warranty Customer’s Record