Panasonic TH-50PWD6, TH-42PWD6 Safety Precautions, Setup, When using the Plasma Display

Page 4

Safety Precautions

WARNING

Setup

This Plasma Display is for use only with the following optional accessories. Use with any other type of optional accessories may cause instability which could result in the possibility of injury.

(All of the following accessories are manufactured by Matsushita Electric Industrial Co., Ltd.)

• Speakers

TY-SP42P5W-K (TH-42PWD6, TH-42PHD6),

• Pedestal

TY-SP50P5W-K (TH-50PHD6)

TY-ST05-K

• Wall stand

TY-ST42PW1

• Mobile stand

TY-ST42PF3

• Wall-hanging bracket (vertical)

TY-WK42PV1

• Wall-hanging bracket (angled)

TY-WK42PR1

• Wall-hanging bracket (drawer type)

TY-WK42DR1

• Ceiling unit

TY-CE42PS1

• BNC Component Video Terminal Board

TY-42TM6A

• BNC Composite Video Terminal Board

TY-42TM6B

• RCA Component Video Terminal Board

TY-42TM6Z

• RCA Composite Video Terminal Board

TY-42TM6V

• RGB (Digital) Terminal Board

TY-42TM6D

• RGB Active Through Terminal Board

TY-42TM6G

• PC Input Terminal Board

TY-42TM6P

• Composite / Component Video Terminal Board

TY-42TM6Y

Always be sure to ask a qualified technician to carry out set-up.

Do not place the Plasma Display on sloped or unstable surfaces.

•The Plasma Display may fall off or tip over.

Do not place any objects on top of the Plasma Display.

•If water is spills onto the Plasma Display or foreign objects get inside it, a short-circuit may occur which could result in fire or electric shock. If any foreign objects get inside the Plasma Display, please consult your local Panasonic dealer.

If using the pedestal (optional accessory), leave a space of at least 10 cm at the top, left and right, at least 6 cm at the bottom, and at least 7 cm at the rear. If using some other setting-up method, leave a space of at least 10 cm at the top, bottom, left and right, and at least 1.9 cm at the rear.

Avoid installing this product near electronic equipment that is easy to receive electromagnetic waves.

•It will cause interference in image, sound, etc. In particular, keep video equipment away from this product.

When using the Plasma Display

The Plasma Display is designed to operate on 220 - 240 V AC, 50/60 Hz.

Do not cover the ventilation holes.

•Doing so may cause the Plasma Display to overheat, which can cause fire or damage to the Plasma Display.

Do not stick any foreign objects into the Plasma Display.

•Do not insert any metal or flammable objects into the ventilations holes or drop them onto the Plasma Display, as doing so can cause fire or electric shock.

Do not remove the cover or modify it in any way.

•High voltages which can cause severe electric shocks are present inside the Plasma Display. For any inspection, adjustment and repair work, please contact your local Panasonic dealer.

Securely insert the power cord plug as far as it will go.

•If the plug is not fully inserted, heat may be generated which could cause fire. If the plug is damaged or the wall socket plate is loose, they shall not be used.

Do not handle the power cord plug with wet hands.

•Doing so may cause electric shocks.

Do not do anything that may damage the power cable. When disconnecting the power cable, pull on the plug body, not the cable.

•Do not damage the cable, make any modifications to it, place heavy objects on top of it, heat it, place it near any hot objects, twist it, bend it excessively or pull it. To do so may cause fire and electric shock. If the power cable is damaged, have it repaired at your local Panasonic dealer.

If the Plasma Display is not going to be used for any prolonged length of time, unplug the power cord plug from the wall outlet.

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Operating Instructions High Definition Plasma DisplayEnglish Model No. TH-42PWD6Table of Contents Important Safety Notice Trademark CreditsSetup Safety PrecautionsWhen using the Plasma Display If problems occur during use Cleaning and maintenanceElectric shocks can result if this is not done Accessories Supply AccessoriesRemote Control Batteries Connections SpeakersTerminals L Speakers Terminals R AC cord connection see AC cord fixingSignal Names for D-sub 15P Connector GND Ground Signal NamePC Input Terminals connection SDA HD/SYNC SCLInstalling the ferrite core Large size CommandSerial Terminals connection Communication parametersBasic Controls Off Power On/Off and input signal selection Power On/OffConnecting the plug to the Wall Outlet AC cord connectionSelect the input signal Selecting the On-Screen Menu LanguageINPUT1 INPUT2 INPUT3 EnglishusOn-Screen Menu Displays Press to access each adjust screen From the unit Press to SetupTo setup Multidisplay screen Press to Set upAspect Controls Adjusting screen Adjusting Picture Pos./SizeHelpful Hint N / Normalise Normalisation Picture Adjustments NormalDynamic CinemaAdvanced settings AGCSound Adjustment MuteDigital Zoom Display the Operation GuideSelect the area of the image to be enlarged Select the magnification required for the enlarged displayPresent Time Setup / Set up Timer Present Time SetupPress to exit from Present Time Setup Present TimeSet up Timer Display the Set up Timer screen Press to selectMode selection Start settingScreensaver For preventing after-images Reversal / Scroll selectionReduces screen after-image Setup of Screensaver TimePress to select Screensaver Side Panel Adjustment This function may be applicable to the non-picture areaCustomizing the Input labels Reduces power consumptionINPUT3/VIDEO3/COMPONENT3/RGB3/PC3/DVD3/CATV3/VCR3/STB3 Setup for Multi Display How to Setup Multi DisplayPress to select 2 ⋅ 2, 3 ⋅ Setup for Input Signals Component/RGB-in Select3D Y/C Filter For Ntsc AV images RGBColour system / Panasonic Auto Cinema realityIf the picture image becomes unstable PAL Secam NtscSetting RGB sync signal SyncFreq. kHz/V-Freq. Hz Displays the H Horizontal/V Vertical frequenciesTroubleshooting Plasma Display panel Symptoms CheckInput signal can be displayed MarkSpecifications TH-42PWD6 TH-42PHD6 TH-50PHD6Customer’s Record
Top Page Image Contents