Panasonic TH-50PWD6, TH-42PWD6 Accessories Supply, Remote Control Batteries

Page 6

Accessories

Accessories Supply

Check that you have the accessories and items shown

Operating Instruction book

Remote Control

Transmitter

EUR646529

INPUT

SURROUND

VOL

Batteries for the Remote Control Transmitter

(2 ⋅ R6 Size)

N		R
PICTURE	SOUND	SET UP
MULTI	SWAP SELECT	MOVE
PIP	SWAP SELECT	MOVE
PICTURE
POS. /SIZE		ASPECT
PC	OFF TIMER

PLASMA DISPLAY

AC cord

Fixing bands

Ferrite core (small size) ⋅ 1

Ferrite core (large size) ⋅ 2

Remote Control Batteries

Requires two R6 batteries.

1.Turn the transmitter face down. Press and slide off the battery cover.

2.Install the batteries as shown in the battery compartment. (Polarity + or – must match the markings in the compartment.)

3.Replace the cover and slide in reverse until the lock snaps.

Two “R6” size

Helpful Hint:

For frequent remote control users, replace old batteries with

Alkaline batteries for longer life.

Precaution on battery use

Incorrect installation can cause battery leakage and corrosion that will damage the remote control transmitter.

Observe the following precaution:

1.Batteries shall always be replaced as a pair. Always use new batteries when replacing the old set.

2.Do not combine a used battery with a new one.

3.Do not mix battery types (example: “Zinc Carbon” with “Alkaline”).

4.Do not attempt to charge, short-circuit, disassemble, heat or burn used batteries.

5.Battery replacement is necessary when remote control acts sporadically or stops operating the Plasma Display set.

6

Image 6

Contents English Operating InstructionsHigh Definition Plasma Display Model No. TH-42PWD6Table of Contents Important Safety Notice Trademark CreditsSafety Precautions SetupWhen using the Plasma Display Cleaning and maintenance If problems occur during useElectric shocks can result if this is not done Accessories Accessories SupplyRemote Control Batteries Terminals L Speakers Terminals R AC cord connection see ConnectionsSpeakers AC cord fixingPC Input Terminals connection Signal Names for D-sub 15P ConnectorGND Ground Signal Name SDA HD/SYNC SCLSerial Terminals connection Installing the ferrite core Large sizeCommand Communication parametersBasic Controls Off Connecting the plug to the Wall Outlet Power On/Off and input signal selectionPower On/Off AC cord connectionINPUT1 INPUT2 INPUT3 Select the input signalSelecting the On-Screen Menu Language EnglishusOn-Screen Menu Displays To setup Multidisplay screen Press to access each adjust screen From the unitPress to Setup Press to Set upAspect Controls Adjusting Picture Pos./Size Adjusting screenHelpful Hint N / Normalise Normalisation Dynamic Picture AdjustmentsNormal CinemaAdvanced settings AGCSound Adjustment MuteSelect the area of the image to be enlarged Digital ZoomDisplay the Operation Guide Select the magnification required for the enlarged displayPress to exit from Present Time Setup Present Time Setup / Set up TimerPresent Time Setup Present TimeSet up Timer Display the Set up Timer screen Press to selectScreensaver For preventing after-images Mode selectionStart setting Reversal / Scroll selectionSetup of Screensaver Time Reduces screen after-imagePress to select Screensaver Side Panel Adjustment This function may be applicable to the non-picture areaReduces power consumption Customizing the Input labelsINPUT3/VIDEO3/COMPONENT3/RGB3/PC3/DVD3/CATV3/VCR3/STB3 Setup for Multi Display How to Setup Multi DisplayPress to select 2 ⋅ 2, 3 ⋅ 3D Y/C Filter For Ntsc AV images Setup for Input SignalsComponent/RGB-in Select RGBIf the picture image becomes unstable Colour system / Panasonic AutoCinema reality PAL Secam NtscFreq. kHz/V-Freq. Hz Setting RGB sync signalSync Displays the H Horizontal/V Vertical frequenciesTroubleshooting Plasma Display panel Symptoms CheckInput signal can be displayed MarkSpecifications TH-42PWD6 TH-42PHD6 TH-50PHD6Customer’s Record